Bedienungsanleitung Makita DJR188 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691887

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

7 ENGLISH

Pulltheswitchtriggertolightupthelamp.Thelamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: When the tool is overheated, the lamp blinks

for one minute. In this case, cool down the tool before

another operation.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing the recipro

saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the blade and around the

blade clamp.Failuretodosomaycauseinsufcient

tighteningoftheblade,resultinginaseriousinjury.

Toinstallthereciprosawblade,alwaysmakesurethat

the blade clamp lever (part of the blade clamp sleeve)

is in released position on the insulation cover before

inserting the recipro saw blade. If the blade clamp lever

isinxedposition,rotatethebladeclampleverinthe

direction of the arrow so that it can be locked at the

released positon .

►Fig.5: 1. Blade clamp lever 2. Released position

3. Fixed position

Insert the recipro saw blade into the blade clamp as far

asitwillgo.Thebladeclampsleeverotatesandxes

the recipro saw blade. Make sure that the recipro saw

blade cannot be extracted even though you try to pull

it out.

►Fig.6: 1. Recipro saw blade 2. Blade clamp sleeve

CAUTION: If you do not insert the recipro saw

blade deep enough, the recipro saw blade may be

ejected unexpectedly during operation.Thiscan

be extremely dangerous.

Toremovethereciprosawblade,rotatetheblade

clampleverinthedirectionofthearrowfully.Thereci-

pro saw blade is removed and the blade clamp lever is

xedatthereleasedposition .

►Fig.7: 1. Recipro saw blade 2. Blade clamp lever

CAUTION: Keep hands and ngers away from

the lever during the switching operation. Failure

to do so may cause personal injuries.

NOTE: If you remove the recipro saw blade without

rotating the blade clamp lever fully, the lever may not

be locked in the released position . In this case,

rotate the blade clamp lever fully again, then make

sure that the blade clamp lever locked at the released

position .

NOTE: If the blade clamp lever is positioned inside

thetool,switchonthetooljustasecondtoletthe

blade out. Remove the battery cartridge from the tool

before installing or removing the recipro saw blade.

OPERATION

CAUTION: Always press the shoe rmly

against the workpiece during operation. If the

shoe is removed or held away from the workpiece

duringoperation,strongvibrationand/ortwistingwill

be produced, causing the blade to snap dangerously.

CAUTION: Always wear gloves to protect

your hands from hot ying chips when cutting

metal.

CAUTION: Be sure to always wear suitable

eye protection which conforms with current

national standards.

CAUTION: Always use a suitable coolant

(cutting oil) when cutting metal. Failure to do so will

cause premature blade wear.

CAUTION: Do not quirk the blade during

cutting.

Presstheshoermlyagainsttheworkpiece.Donot

allow the tool to bounce. Bring the recipro saw blade

into light contact with the workpiece. First, make a pilot

grooveusingaslowerspeed.Thenuseafasterspeed

to continue cutting.

►Fig.8

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DJR188 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info