Bedienungsanleitung Makita DJR360 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691888

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

7 ENGLISH

►Fig.4: 1.Lock/speedchangelever2. Switch trigger

3.Statusofthelock/speedchangelever

►Fig.5

Tostartthetool,depressthelock/speedchangelever

fromeitherAorBsideandpulltheswitchtrigger.

Toolspeedisincreasedbyincreasingpressureonthe

switch trigger. Release the switch trigger to stop.

Maxtoolspeedcanbechangedin2steps.

• For high speed

Whenthelock/speedchangeleverisdepressed

fromAside,thestrokespeedisat“2”.

• For low speed

Whenthelock/speedchangeleverisdepressed

from B side, the stroke speed is at “1”.

Whenthelock/speedchangeleverisin

position, the

toolislockedandtheswitchtriggercannnotbepulled.

Lighting up the front lamp

►Fig.6: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keepsonlightingwhiletheswitchtriggerisbeingpulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE:Whenthetoolisoverheated,thelampblinks

foroneminute.Inthiscase,cooldownthetoolbefore

another operation.

Adjusting the shoe

If Provided (Country specic)

Whenthereciprosawbladelosesitscuttingefciency

in one place along its cutting edge, reposition the shoe

to utilize a sharp, unused portion of its cutting edge.

Thiswillhelptolengthenthelifeofthereciprosaw

blade.

Thepositionoftheshoecanbeadjustedinvelevels.

Torepositiontheshoe,opentheshoeadjustinglever

andselectthesuitableposition,thenclosetheshoe

adjustinglever.

►Fig.7: 1. Shoe 2.Shoeadjustinglever

NOTE:Theshoecannotbeadjustedwithoutopening

theshoeadjustingleverfully.

Hook

CAUTION: When hanging the tool, set the

lock/speed change lever in position to lock

the switch trigger. (See the section titled “Switch

action” .)

CAUTION: Never hang the tool at high or

potentially unstable location.

►Fig.8: 1. Hook

Thehookisconvenientforhangingthetooltemporarily.

Tousethehook,simplyliftuphookuntilitsnapsinto

the open position.

When not in use, always lower hook until it snaps into

the closed position.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing the recipro

saw blade

CAUTION: Always clean out all chips or for-

eign matter adhering to the blade and around the

blade clamp.Failuretodosomaycauseinsufcient

tighteningoftheblade,resultinginaseriousinjury.

Toinstallthereciprosawblade,alwaysmakesurethat

thebladeclamplever(partofthebladeclampsleeve)

is in released position

ontheinsulationcoverbefore

insertingthereciprosawblade.Ifthebladeclamplever

isinxedposition,rotatethebladeclampleverinthe

directionofthearrowsothatitcanbelockedatthe

released positon .

►Fig.9: 1. Blade clamp lever 2. Released position

3. Fixed position

Insertthereciprosawbladeintothebladeclampasfar

asitwillgo.Thebladeclampsleeverotatesandxes

thereciprosawblade.Makesurethatthereciprosaw

bladecannotbeextractedeventhoughyoutrytopull

it out.

►Fig.10: 1.Reciprosawblade2. Blade clamp sleeve

CAUTION: If you do not insert the recipro saw

blade deep enough, the recipro saw blade may be

ejected unexpectedly during operation.Thiscan

beextremelydangerous.

Toremovethereciprosawblade,rotatetheblade

clampleverinthedirectionofthearrowfully.Thereci-

prosawbladeisremovedandthebladeclampleveris

xedatthereleasedposition

►Fig.11: 1.Reciprosawblade2. Blade clamp lever

CAUTION: Keep hands and ngers away from

the lever during the switching operation. Failure

to do so may cause personal injuries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DJR360 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info