Bedienungsanleitung Makita DJS100 (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600410

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

properly and returns to the “OFF” position when the

rear of the switch lever is depressed.

• Switch can be locked in “ON” position for ease of

operator comfort during extend use. Apply caution

when locking tool in “OFF” position and maintain firm

grasp on tool.

To start the tool, slide the switch lever toward the “I (ON)”

position. For continuous operation, press the front of the

switch lever to lock it.

To stop the tool, press the rear of the switch lever, then

slide it toward the “O (OFF)” position.

Indication lamp with multi function

(Fig. 4)

Indication lamps are located in two positions.

- Battery cartridge replacing signal

- When the battery power is almost used up during

operation, the red lamp lights up and the tool stops

immediately. Replace the battery with fully charged

one when the red lamp lights up.

- Accidental re-start preventive function

- Even if the battery cartridge is inserted on the tool

with the slide switch in the “I (ON)” position, the tool

does not start. At this time, the lamp flickers slowly

and this shows that the accidental re-start

preventive function is at work.

- To start the tool, first slide the slide switch toward the

“O (OFF)” position and then slide it toward the “I

(ON)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Adjusting the blade clearance

For DJS160 and DJS161 only

Adjust the clearance between the side blade and the

center blade according to the thickness of the workpiece.

(Fig. 5)

First use a hex wrench to loosen the screw. (Fig. 6)

Then use the hex wrench to adjust the clearance by

tightening or loosening the bolt. There may be a slight

difference between clearance of both sides of the center

blade.

Check the smaller clearance with the thickness gauge

and adjust it.

When using the thickness gauge to adjust the blade

clearance, refer to the table.

006428

After adjusting the clearance, tighten the screw securely.

Storing hex wrench (Fig. 7)

Store the hex wrench as shown in the figure when not in

use.

OPERATION

Lubrication (Fig. 8)

Before operation, lubricate the contact point of the center

blade and the pin. To keep good cutting performance, also

use a cutting lubricant from time to time during operation.

OPERATION (Fig. 9)

Turn the tool on and set front ends of the side blades on

the workpiece. Now simply move the tool forward,

keeping the side blades flush with the workpiece surface.

(Fig. 10)

CAUTION:

• When cutting a small portion of the workpiece, you may

have difficulty completing the end of the cut. In that

case, try to cut it again, pulling the workpiece back

slightly.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

NOTICE:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed.

Replacing carbon brushes (Fig. 11)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes.

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it up.

(Fig. 12)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 13)

Reinstall the holder cap cover on the tool.

Replacing blades

The service life of the blades varies in terms of the

workpiece to be cut. The following reference tables

indicate the approximate service life of the blades.

When the blades become dull, ask Makita Authorized

Service Centers to replace the blades.

Workpiece thickness

(mm)

Marking on thickness

gauge

Less than 0.8 0.5

0.8 - 1.3 1.0

More than 1.3 1.5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DJS100 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info