Bedienungsanleitung Makita DLW140 (Seite 7 von 21) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691731

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

7 ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specications provided with this

power tool.Failuretofollowallinstructionslistedbelow

mayresultinelectricshock,reand/orseriousinjury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your mains-oper-

ated(corded)powertoolorbattery-operated(cordless)powertool.

Cut-off machine safety warnings

1. Position yourself and bystanders away from

the plane of the rotating wheel. The guard helps

toprotecttheoperatorfrombrokenwheelfrag-

ments and accidental contact with wheel.

Use only bonded reinforced cut-off wheels for your

power tool.Justbecauseanaccessorycanbeattached

to your power tool, it does not assure safe operation.

3. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool.Accessoriesrunningfasterthan

theirratedspeedcanbreakandyapart.

Wheels must be used only for recommended

applications. For example: do not grind with the

side of a cut-off wheel.Abrasivecut-offwheelsare

intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

5. Always use undamaged wheel anges that are

of correct diameter for your selected wheel.

Properwheelangessupportthewheelthus

reducingthepossibilityofwheelbreakage.

6. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannotbeadequatelyguardedorcontrolled.

The arbour size of wheels and anges must prop-

erly t the spindle of the power tool. Wheels and

angeswitharbourholesthatdonotmatchthemount-

inghardwareofthepowertoolwillrunoutofbalance,

vibrateexcessivelyandmaycauselossofcontrol.

Do not use damaged wheels. Before each use, inspect

the wheels for chips and cracks. If the power tool or

wheel is dropped, inspect for damage or install an

undamaged wheel. After inspecting and installing the

wheel, position yourself and bystanders away from

the plane of the rotating wheel and run the power tool

at maximum no load speed for one minute. Damaged

wheelswillnormallybreakapartduringthistesttime.

Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and shop apron capable

of stopping small abrasive or workpiece fragments.

Theeyeprotectionmustbecapableofstoppingying

debrisgeneratedbyvariousoperations.Thedustmask

orrespiratormustbecapableofltratingparticles

generatedbyyouroperation.Prolongedexposureto

high intensity noise may cause hearing loss.

10. Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragmentsofworkpieceorofabrokenwheelmay

yawayandcauseinjurybeyondimmediatearea

of operation.

11. Regularly clean the power tool’s air vents. The

motor’s fan can draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

12. Do not operate the power tool near ammable

materials. Do not operate the power tool while

placed on a combustible surface such as

wood. Sparks could ignite these materials.

13. Do not use accessories that require liquid

coolants.Usingwaterorotherliquidcoolants

may result in electrocution or shock.

Kickback and related warnings

Kickbackisasuddenreactiontoapinchedorsnagged

rotatingwheel.Pinchingorsnaggingcausesrapidstalling

of the rotating wheel which in turn causes the uncontrolled

cuttingunittobeforcedupwardstowardtheoperator.

Forexample,ifanabrasivewheelissnaggedorpinched

bytheworkpiece,theedgeofthewheelthatisentering

into the pinch point can dig into the surface of the mate-

rialcausingthewheeltoclimboutorkickout.Abrasive

wheelsmayalsobreakundertheseconditions.

Kickbackistheresultofpowertoolmisuseand/or

incorrectoperatingproceduresorconditionsandcanbe

avoidedbytakingproperprecautionsasgivenbelow.

Maintain a rm grip on the power tool and posi-

tion your body and arm to allow you to resist

kickback forces. The operator can control upward

kickbackforces,ifproperprecautionsaretaken.

2. Do not position your body in line with the

rotating wheel.Ifkickbackoccurs,itwillpropel

the cutting unit upwards toward the operator.

Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such

bladescreatefrequentkickbackandlossofcontrol.

4. Do not “jam” the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases

theloadingandsusceptibilitytotwistingorbinding

ofthewheelinthecutandthepossibilityofkick-

backorwheelbreakage.

5. When the wheel is binding or when interrupt-

ing a cut for any reason, switch off the power

tool and hold the cutting unit motionless until

the wheel comes to a complete stop. Never

attempt to remove the wheel from the cut while

the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to

eliminatethecauseofwheelbinding.

Do not restart the cutting operation in the work-

piece. Let the wheel reach full speed and carefully

re-enter the cut.Thewheelmaybind,walkupor

kickbackifthepowertoolisrestartedintheworkpiece.

7. Support any oversized workpiece to minimize

the risk of wheel pinching and kickback. Large

workpieces tend to sag under their own weight.

Supportsmustbeplacedundertheworkpiece

near the line of cut and near the edge of the work-

pieceonbothsidesofthewheel.

Makita DLW140 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info