Bedienungsanleitung Makita DP4002 (Seite 5 von 8) (Englisch, Holländisch)

600285

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ENGLISH

Explanation of general view

1Tighten

2 Chuck key

3Sleeve

4 Ring

5 Switch trigger

6 Lock lever

7 Reversing switch lever

8 Side grip

9Protrusions

10 Teeth

11 Loosen

12 Depth gauge

13 Reaction

14 Reverse

15 Forward

16 Holding against a stud.

17 Holding against a floor.

18 Hook

SPECIFICATIONS

Model DP3002 DP3003 DP4000 DP4001 DP4002 DP4003

Capacities

Steel ............................................. 10 mm 10 mm 13 mm 13 mm 13 mm 13 mm

Wood ............................................ 32 mm 32 mm 38 mm 38 mm 38 mm 38 mm

No load speed (min

–1

) ..................... 0 – 1,200 0 – 1,200 0 – 900 0 – 900 0 – 600 0 – 600

Overall length .................................. 304 mm 296 mm 304 mm 308 mm 304 mm 308 mm

Net weight ........................................ 2.0 kg 1.8 kg 2.2 kg 2.0 kg 2.2 kg 2.0 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

SPECIFIC SAFETY RULES

GEB001-2

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to drill safety rules. If you use this power tool

unsafely or incorrectly, you can suffer serious per-

sonal injury.

1. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tools

may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the opeator.

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

8. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated in

this instruction manual may cause serious personal

injury.

OPERATING INSTRUCTIONS

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the side grip, bit

or other accessories.

Installing or removing drill bit

For DP3002, DP4000, DP4002 (Fig. 1)

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each

of the three holes and tighten clockwise. Be sure to

tighten all three chuck holes evenly. To remove the bit,

turn the chuck key counterclockwise in just one hole,

then loosen the chuck by hand. After using the chuck key,

be sure to return it to the original position.

For DP3003, DP4001, DP4003 (Fig. 2)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck. To remove the bit, hold the ring and

turn the sleeve counterclockwise.

Switch action (Fig.3)

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

For continuous operation, pull the trigger and then push

the lock lever upward. To stop the tool from the locked

position, pull the trigger fully, then release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DP4002 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DP4002

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info