Bedienungsanleitung Makita DPB181 (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600238

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Lighting up the lamp (Fig. 4)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The lamp goes out just after releasing the trigger.

NOTICE:

• Do not apply impact to the lamp, which may cause

damage or shorted service time to it.

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• Do not use thinner or gasoline to clean the lamp. Such

solvents may damage it.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing the blade

CAUTION:

• Oil on the blade can cause the blade to slip or come off

unexpectedly. Wipe off all excess oil with a cloth before

installing the blade.

• Always wear protective gloves when handling the

blade.

• Use caution when handling the blade to avoid cut by

the sharp edge of the blade teeth.

• Keep your body away from the blade area when

checking the blade movement.

• When turning the blade tightening lever clockwise to

release the tension on the blade, point the tool

downward because the blade may come off

unexpectedly.

To install the blade: (Fig. 5)

1. Turn the blade tightening lever clockwise until it stops

to loosen the wheel.

2. Match the direction of the arrows on the blade and on

the wheels.

3. Insert the non-serrated side of the blade into the upper

holder and lower holder. Make sure the blade in both

upper and lower holder touches to the bottom

bearings. (Fig. 6 & 7)

4. With pressing the middle part of the blade, position the

blade around one wheel. Moving the wheel to A side

makes it easier to do so. (Fig. 8)

5. Position the blade on another wheel similarly.

6. Position the edge of the blade on rubber tire.

7. Hold the blade in place and turn the blade-tightening

lever counterclockwise until it stops. This places

proper tension on the blade.

Make sure that the blade is correctly positioned around

the wheels.

Start and stop the tool two or three times to make sure

that the blade runs properly on the wheels.

To remove the blade, follow the installation procedure in

reverse.

Adjusting the stopper plate position

(Fig. 9)

In the ordinary operation, protrude the stopper plate to the

A side fully.

When the stopper plate strikes against the obstacles like a

wall or the like at the finishing of a cut, loosen two screws

and slide it to the B side in the figure.

After sliding the stopper plate, secure it by tightening two

screws firmly.

Hook (optional accessory) (Fig. 10)

Hook is useful for hanging the tool. Hang tool on a pipe

vice or other suitable, stable structure.

To install the hook, set the hook alongside the groove and

tighten it with two screws.

Wheel cover (optional accessory)

To install the wheel cover:

1. Put together the hinges of the wheel cover and the

tool.

2. Insert the axes. (Fig. 11)

3. Fasten the axes by the stop rings. (Fig. 12)

4. Lock the wheel cover.

NOTICE:

When opening the wheel cover, press and open both the

stoppers simultaneously. Opening only one stopper may

cause crack on the wheel cover.

OPERATION

CAUTION:

• Always hold front and rear handle. Never hold the

tool body or guards. Hands may slip from these

locations and contact blade. Contact with the blade

may result in personal injury.

• Make sure to hold the tool firmly when turning on or off

the tool or when cutting. Otherwise the tool may fall

and cause personal injury.

For stable cut, always keep at least two teeth in the cut.

(Fig. 13)

Select the proper cutting position for your workpiece by

referring to the figure. (Fig. 14)

Hold the tool with both hands as shown in the figure.

(Fig. 15)

Before turning on the tool, always make sure that the

stopper plate contacts the workpiece and the blade is

clear of the workpiece.

Turn the tool on and wait until the blade attains full speed.

Gently lower the blade into the cut. The weight of the tool

or slightly pressing the tool will supply adequate pressure

for the cutting. Do not force the tool.

As you reach the end of a cut, release pressure and lift it

slightly so that it will not fall against the workpiece.

NOTICE:

• Applying excessive pressure to the tool or twisting of

the blade may cause bevel cutting or damage to the

blade.

• When not using the tool for a long period of time,

remove the blade from the tool.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DPB181 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info