Bedienungsanleitung Makita DPB182 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691826

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 ENGLISH

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keepsonlightingwhiletheswitchtriggerisbeing

pulled.Thelampgoesoutjustaftertheswitchtriggeris

released.

►Fig.4: 1. Lamp

NOTE: Do not apply impact to the lamp, which may

cause damage or shorted service time to it.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing the band saw blade

CAUTION: Oil on the band saw blade can

cause the blade to slip or come off unexpectedly.

Wipe off all excess oil with a cloth before install-

ing the band saw blade.

CAUTION: Always wear protective gloves

when handling the band saw blade.

CAUTION: Use caution when handling the

band saw blade to avoid cut by the sharp edge of

the blade teeth.

CAUTION: Keep your body away from

the band saw blade when checking the blade

movement.

CAUTION: When turning the blade tightening

lever clockwise to release the tension on the band

saw blade, point the tool downward because the

band saw blade may come off unexpectedly.

►Fig.5: 1. Tighten 2. Loosen 3. Blade tightening lever

Toinstallthebandsawblade:

1. Turnthebladetighteningleverclockwiseuntilit

stops to loosen the wheel.

2. Matchthedirectionofthearrowsonthebandsaw

bladeandonthewheels.

3. Insertthenon-serratedsideofthebandsawblade

into the upper holder and lower holder. Make sure the

bandsawbladeinbothupperandlowerholdertouches

tothebottombearings.

►Fig.6: 1. Lower holder 2. Upper holder 3. Bottom

bearing

4. Withpressingthemiddlepartofthebandsaw

blade,positionthebladearoundonewheel.Movingthe

wheeltoAsidemakesiteasiertodoso.

►Fig.7: 1. Wheel 2.Rubbertire

5. Positionthebandsawbladeonanotherwheel

similarly.

6. Positiontheedgeofthebandsawbladeonrubber

tire.

7. Holdthebandsawbladeinplaceandturnthe

bladetighteninglevercounterclockwiseuntilitstops.

Thisplacespropertensiononthebandsawblade.

NOTICE: Make sure that the band saw blade is

correctly positioned around the wheels.

NOTICE: Start and stop the tool two or three

times to make sure that the band saw blade runs

properly on the wheels.

Toremovethebandsawblade,followtheinstallation

procedure in reverse.

Adjusting the stopper plate position

In the ordinary operation, protrude the stopper plate to

theAsidefully.

Whenthestopperplatestrikesagainsttheobstacles

likeawallorthelikeatthenishingofacut,loosentwo

boltsandslideittotheBsideinthegure.

Afterslidingthestopperplate,secureitbytightening

twoboltsrmly.

►Fig.8: 1. Stopper plate 2. Bolts 3.Bandsawblade

Installing hook

Optional accessory

CAUTION: Do not use the hook for other pur-

pose than temporarily hanging the tool. Doing so

may cause the hook come off from the tool and result

inpersonalinjury.

Hook is useful for hanging the tool. Hang the tool on a

pipeviceorothersuitable,stablestructure.

To install the hook, set the hook alongside the groove

and tighten it with two screws.

►Fig.9: 1. Hook 2. Screws

OPERATION

CAUTION: Always insert the battery cartridge

all the way until it locks in place. If you can see the

redindicatorontheuppersideofthebutton,itisnot

locked completely. Insert it fully until the red indicator

cannotbeseen.Ifnot,itmayaccidentallyfalloutof

thetool,causinginjurytoyouorsomeonearound

you.

CAUTION: Always hold front and rear handle.

Never hold the tool body or guards. Hands may

slipfromtheselocationsandcontactwiththeband

sawblade.Itmayresultinpersonalinjury.

CAUTION: Make sure to hold the tool rmly

when turning on or off the tool or when cutting.

Otherwisethetoolmayfallandcausepersonalinjury.

NOTE: When cutting metal, wearing gloves is recom-

mendedtoprotectyourhandsfromhotyingchips.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DPB182 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info