Bedienungsanleitung Makita DPT350 (Seite 6 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600236

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

properly and returns to the “OFF” position when

released. (Fig. 4)

The tool is provided with lever as a safety system in

addition to the usual trigger. (Fig. 5)

To fire pin-nails, first pull the lever and then pull the

trigger.

Adjusting the depth of pin-nailing

WARNING:

• Always make sure that your fingers are not placed on

the trigger or the lever and the battery cartridge is

removed before loading the pin nailer. (Fig. 6)

Depth of pin-nailing can be adjusted on this pin nailer.

Turn two bolts a quarter turn using the hex wrench

provided with the tool and the driver guide cover will slide

up or down. Depth can be adjusted 1.5 mm to the

maximum. At desired depth, secure it with two bolts firmly.

Lighting up the lamps

CAUTION:

• Do not look in the light or see the source of light

directly. (Fig. 7)

To turn on the lamp, pull the lever. Release the lever to

turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• Even if the lamp lights up when the battery power

residual gets small, pin nailer may not fire pin nails. In

this case, charge the battery cartridge.

Anti-dry firing device

CAUTION:

• Always make sure that your fingers are not placed on

the trigger or the lever and the battery cartridge is

removed before loading the pin nailer.

When the number of remaining pin nails in the magazine

are 0 - 3 pcs., the trigger can no longer be pulled. At this

time, insert a new strip of pin nails in the magazine and

the trigger can be pulled again.

NOTE:

• When firing a different length of pin nails shortly after

the anti- dry firing device has actuated, insert a new

strip of pin nails into the magazine and fire away all the

prior pin nails that have remained on junk material.

ASSEMBLY

CAUTION:

• Always make sure that your fingers are not placed on

the trigger or the lever and the battery cartridge is

removed before carrying out any work on the pin nailer.

Loading the pin nailer

CAUTION:

• Always make sure that your fingers are not placed on

the trigger or the lever and the battery cartridge is

removed before loading the pin nailer.

• Do not abruptly slide the magazine of the pin nailer

loaded with pin nails. Accidentally dropping pin nails

especially when working in high places may cause

personal injuries.

• Load pin nails in the correct direction. Loading in wrong

direction may cause premature wear and tear of the

driver and damage of the other parts. (Fig. 8)

Remove the battery cartridge.

Press the locking lever and slide the magazine.

Place pin nails against the magazine and insert into the

slit all the way. (Be careful to place pin nails in the right

direction.)

Keeping pin nails in this position, insert these nails all the

way into the driver guide.

Return the magazine to the original position and lock it

with the locking lever.

CAUTION:

• Do not use deformed connected pin nails. Use pin nails

specified in this manual. Using pin nails other than

those specified may cause pin nail jamming and

breakage of the pin nailer.

Unloading pin nailer

CAUTION:

• When removing pin nails, make sure that your fingers

are not placed on the trigger or the lever and the

battery cartridge is removed from the pin nailer.

Misfiring may cause personal injuries and property

damage.

Remove the battery cartridge.

Press the locking lever and slide the magazine.

Take out pin nails from the magazine slit.

Nose adapter

CAUTION:

• Always make sure that your fingers are not placed on

the trigger or the lever and the battery cartridge is

removed before installing the nose adapter. (Fig. 9)

When firing pin nails on the material to be fastened with

easily-marred surfaces, use the nose adapter. To install

the nose adapter, place it over the driver guide cover so

that the protrusion inside the nose adapter fits to the slit in

the driver guide cover.

When not in use, store the nose adapter in the holder at

the back end of the magazine to keep it from being lost.

Hook

CAUTION:

• Always make sure that your fingers are not placed on

the trigger or the lever and the battery cartridge is

removed before using the hook. (Fig. 10)

CAUTION:

• Do not hang the hook from the waist belt. Dropping the

pin nailer, which is caused by the hook accidentally

coming out of place, may cause misfiring and personal

injuries. (Fig. 11)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DPT350 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info