Bedienungsanleitung Makita DPT351 (Seite 7 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

600237

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Hex wrench storage (Fig. 12)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

Driving pin nails

WARNING:

• Before pulling the trigger, always make sure that the

opening that pin-nails are fired contacts material to be

fastened. Just pulling the trigger fires pin nails.

Misfiring may cause personal injuries. (Fig. 13)

Place flat the opening of the tool that pin-nails are fired on

the material to be fastened and hold the tool firmly against

the material. Then pull the lever and then pull the trigger

fully to drive the pin nail. The grip is shaped so that the

tool head can be held down securely with index finger and

thumb. After driving a pin-nail, be sure to release the

trigger fully. (Fig. 14)

When the head of driven pin-nail remains above the

surface of the material, drive the pin-nail while holding the

pin nailer head firmly.

NOTE:

• When the trigger is pulled after a quick trigger action,

the nailer may do nothing but operates momentarily

and may not fire pin nails. This is not a trouble. At this

time, release the trigger once, pull it again and the pin

nails can be fired.

• Using the pin nailer continuously with the head of fired

pin nails remaining above the surface of material to be

fastened may cause damage to the driver of the pin

nailer and nailer jamming etc.

Removing jammed pin nails

WARNING:

• Always make sure that the lever is released and the

battery cartridge is removed before removing jammed

nails. (Fig. 15)

Remove the battery cartridge from the pin nailer.

Take out pin nails that remain inside the magazine.

Loosen bolt (A) and bolt (B) by turning them

approximately two turns using the hex wrench provided

with the pin nailer.

Remove driver guide cover by sliding it.

Remove stuck pin nails, debris, adhesives and woodchips

etc. from the passage for pin nails.

Check the driver guide cover for stuck pin nails or other

foreign matters and then secure it with these two bolts.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

• To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized Service Centers,

always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Pin nails

• Various type of Makita genuine batteries and chargers

• Safety goggles

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model DPT350

Sound pressure level (L

): 75 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DPT351

Sound pressure level (L

): 74 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG904-2

The vibration emission value determined according to

EN60745:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH101-15

EC Declaration of Conformity

We Makita Corporation as the responsible

manufacturer declare that the following Makita

machine(s):

Designation of Machine:

Cordless Pin Nailer

Model No./ Type: DPT350, DPT351

are of series production and

Conforms to the following European Directives:

2006/42/EC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DPT351 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info