Bedienungsanleitung Makita DSC250 (Seite 8 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691889

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

8 ENGLISH

5. Do not short the battery. A battery short can

cause a large current ow, overheating, pos-

sible burns and even a breakdown.

· Do not touch the terminals with any conductive

materials.

· Avoid storing battery in a container with other

metal objects such as nails, coins, etc.

· Do not expose battery to water or rain.

· Do not cut the cord.

6. Do not operate the tool or charge the battery in

explosive atmospheres, such as in the presence

of lacquer, paint, benzin, thinner, gasoline, gasses

or adhesive. This may cause an explosion or re.

7. Do not charge the battery on paper, cardboard,

cloth, cushions, mats, carpets, vinyl or in the pres-

ence of dust. This may cause re.

8. Do not expose the Charger to water or metal items

that can short out the charging terminals.

9. Do not use charger for any other purpose than

charging the battery.

10. Make sure tipped saw blades have no chips or

cracks before using the tool.

11. Do not use water or cutting oil when cutting.

12. Use only Makita genuine tipped saw.

13. Do not leave the tool on the oor with switch

locked on. The tool will run continuously and it

may cause personal injury.

14. Do not operate the tool close to ammable and

fragile items or personnel not necessary to the

operation. During cutting hot debris and sparks will

be ejected from the tool which may cause damage

to the surroundings, re or personal injury.

15. Do not cut concrete. It causes damage to the tool

and may result in personal injury.

16. Check for the presence of people on the ground

during operation in an elevated place. Any materi-

als or tools dropped may cause an accident.

17. If during charging, there is an abnormal generation

of heat, stop charging immediately by disconnect-

ing the battery. Continuing charging may cause

smoke, re or explosion.

18. Do not allow anything to cover or clog the motor

vents.

This may cause the motor to overheat.

19. When using an extension cord with the charger,

it is recommended to use a cord with the cross

section below and with a length as short as pos-

sible. For charging outdoors, use a cord rated for

outdoor use.

Relation between usable cord thickness and maximum

length

Cord size

(Nominal cross sectional area of

conductor)

Maximum cord

length

0.75 mm

20 m

1.25 mm

30 m

WARNING FOR USING

TIPPED SAW

Work area safety

1. Ensure the Dust Bag is xed correctly. Without the

Dust Bag, when Tipped Saw Blades are damaged,

pieces of the blades y off and can cause serious

personal injury.

2. Keep bystanders away from operations. Even with

the Dust Bag tted, damaged blades or hot debris

can y out of the bag, resulting in serious personal

injury.

3. Sparking may occur when cutting with Tipped Saw

Blades. Do not use the tool where there is the risk

of re or explosion.

4. Cutting with Tipped Saw Blades is noisy. Consider

the work area environment.

Dress and protective equipment

5. Wear protective equipment; safety glasses, safety

shoes, dust mask and helmet. Even with the Dust

Bag tted, damaged blades or hot debris can y

out of the cover, resulting in personal injury.

6. Dress properly. Do not wear a tie, loose clothing or

knit gloves. Keep hair covered with a hair cover or

a cap to be away from rotating blades.

Before use

7. Ensure that Tipped Saw Blades are not deformed,

chipped, cracked or worn-out. Do not use a Tipped

Saw if any damage or wear is found. Cutting under

such conditions may cause further damage to the

blades and serious personal injury.

8. Do not use the Tipped Saw for any application

other than that stated in the tool specication.

Using the Tipped Saw for other applications can

cause excessive wear, detachment of blades, low

cutting performance and abnormal generation of

heat, resulting in damage to the blades and seri-

ous personal injury.

Tipped saw replacement

9. When replacing the Tipped Saw, ensure that the

battery is removed from the tool to prevent acci-

dental operation and personal injury.

10. Ensure there is no one in the surroundings before

operation and no abnormal sounds or abnormal

vibrations occur when operating. Operating with

abnormal sounds or abnormal vibrations can dam-

age the blades resulting in serious personal injury.

During operation

11. Do not use the Tipped Saw for any purpose other

than cutting. Do not subject the blades to damage

or stress. It can break the blades resulting in seri-

ous personal injury.

12. Hold the material rmly, in a vice or similar, so

that it cannot move when cutting. If the material

moves, the operation becomes unstable and

cannot be controlled, resulting in damage to the

blades and possible serious personal injury.

13. Start cutting only after the Tipped Saw has

reached maximum speed. If the Tipped Saw is set

against the material before the motor is started,

the blades will be overloaded and damaged,

resulting in possible serious personal injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DSC250 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info