Bedienungsanleitung Makita DSC250 (Seite 11 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691889

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

11 ENGLISH

CAUTION: Hold the tool rmly so that it does

not shake when cutting. Cutting with the tool

shaking will shorten the life of the Tipped Saw and

damage the blades.

CAUTION: Position the tool so it is at 90

degrees to rebar to be cut. If the tool is not at 90

degrees to the rebar, it can cause shaking and

overload the tool.

CAUTION: Do not start cutting immediately

after the motor is switched on. Allow the Tipped

Saw to reach full speed before beginning to cut.

CAUTION: Do not remove the battery when

the motor is switched on. Doing so can cause

damage to the motor’s electronics.

6. After nishing the cut, push down on the rear end

of the Switch which will cause the Switch to move to the

“O” position and turn off the motor.

CAUTION: This tool is designed to cut rebar.

Please contact the manufacturer or your local

dealer if you want to cut other materials. Cutting

other materials will damage the Tipped Saw

blades.

Caution when cutting

1. Ensure that the Tipped Saw blade is well away

from the material to be cut before switching on.

2. Slow down the forward (cutting) movement of the

tool when approaching the end of the cut. This is espe-

cially important when the piece to be cut is less than 50

mm in length. The piece cut off can strike the Tipped

Saw blades, damaging them and cause serious injury.

3. When the Tipped Saw blades become blunt or

chipped. replace the blade. Continuing to use it in this

condition will overload the tool.

4. If the material moves or shakes, when being cut,

stop the operation and properly secure the material.

5. Do not hold by hand the material to be cut. Doing

so may result in personal injury.

6. Do not cut rebar that in size or hardness exceeds

the cutting capacity of the tool.

Replace the Tipped Saw when any

of the below occurs

1. Warning Lamp (red) blinks frequently even though

the battery is fully charged.

2. The Tipped Saw blades are chipped or worn.

3. The cutting speed is very slow.

4. The surface of the cut piece is discolored by heat.

NOTE: Tipped Saw blades cannot be resharpened.

How to t the Dust Bag

► Fig.7: 1. Dust Bag

1. Place the open end of the Dust Bag over the Dust

Bag Holder and secure in place with the draw strings.

2. Give the bag a sharp tug to ensure it is properly

secured.

CAUTION: The Dust Bag is made from non-

ammable material but very hot debris, such as

that produced when cutting with a worn Tipped

Saw blade, can melt the material. Be aware of this

possibility when using the Dust Bag.

Battery Indicator function

► Fig.8: 1. Battery Indicator

When you turn the tool on, the battery indicator shows

the remaining battery capacity. (see table 1)

Table 1

Battery indicator status

Remaining battery

capacity

:On :Off :Blinking

5 0 %-1 0 0 %

2 0 %-5 0 %

0 %-2 0 %

Charge the battery

Automatic speed change function

► Fig.9: 1. Mode Indicator

The tool has ‘high speed mode’ and ‘high torque mode’.

It will select the operating mode automatically, accord-

ing to the work load. When the mode indicator lights up

during operation, the tool is in high torque mode. (see

table 2)

Table 2

Mode indicator status Operation mode

High speed mode

High torque mode

Tool / battery protection function

The tool will automatically stop during operation if the

tool or battery is placed under one of the following

conditions:

- The tool is overloaded

- The tool overheats

If the tool is repeatedly operated under these condi-

tions, the protection system will lock the tool.

Overload protection

If the tool is overloaded during cutting, it will automati-

cally stop. In this situation, turn the tool off and remove

the cause of the overload then restart the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DSC250 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info