Bedienungsanleitung Makita DST221 (Seite 6 von 44) (Deutsch, Englisch, Polnisch)

600230

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

CAUTION:

• Do not use staples other than designated in this

manual or staples that appear to be damaged, bent,

rusty or corroded.

• Do not insert staples of which size is different each

other at the same time inside the magazine ,

causing poor staple feed or jamming.

Loading staples

Remove the battery cartridge.

Press the locking lever on the rear of the sub magazine

and slide the sub magazine backward.

Fig.3

Load staples into the main magazine with their feet

facing up. Slide the sub-magazine forward.

Fig.4

To secure the sub magazine in place, hook the locking

lever on the rear of the sub-magazine.

CAUTION:

• With the magazine loaded, if the tool is held

downward and the sub-magazine is opened, the

staples can fall out and present a danger to anyone

or anything below. Keep this in mind especially

when working in high locations.

Unloading staples

CAUTION:

•

When removing staples, make sure that your fingers

are not placed on the trigger or the lever and the battery

cartridge is removed from the stapler. Misfiring may

cause personal injuries and property damage.

Remove the battery cartridge.

Press the locking lever and slide the magazine back.

Fig.5

Take out staples from the magazine slit.

Fig.6

Hook

CAUTION:

• Always make sure that your fingers are not placed

on the trigger or the lever and the battery cartridge

is removed before using the hook.

Fig.7

CAUTION:

• Do not hang the hook from the waist belt. Dropping

the stapler, which is caused by the hook

accidentally coming out of place, may cause

misfiring and personal injuries.

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

Fig.8

OPERATION

Depth adjustment

Fig.9

If the staples are driven too deep or too shallow, adjust

the driving depth by turning the nut on the bottom of the

tool. For deeper driving of staples, turn the nut clockwise.

For shallower driving, turn the nut counterclockwise.

Please note the nut must be turned in increments of 90°

(1/4 turn) so that the groove on the nut runs parallel to the

magazine.

Driving staples

Fig.10

Place flat the opening of the tool from which staples are

fired on the material to be fastened and hold the tool

firmly against the material. Then pull the lever and then

pull the trigger fully to drive the staples. The grip is

shaped so that the tool head can be held down securely

with index finger and thumb. After driving a staple, be

sure to release the trigger fully.

When the head of driven staple remains above the

surface of material to be fastened, drive the staple while

holding the stapler head firmly.

Fig.11

NOTE:

• Using the stapler continuously with the head of

driven staples remaining above the surface of

material to be fastened may cause damage to the

driver of the stapler and stapler jamming etc..

Checking remaining staples

Fig.12

CAUTION:

• Do not operate the tool without staples. It shortens

the service life of the tool.

There is a convenient sight window on the right side of

the tool (when viewing the tool from the front). Use this

sight window to check if there are staples in the

magazine. When staples are not visible through the

window, load staples into the magazine.

Removing jammed staples

WARNING:

• Always make sure that the trigger are released and

the battery cartridge is removed before removing

jammed staples .

Remove the battery cartridge from the stapler.

Fig.13

Press the locking lever on the rear of the sub magazine

and slide the sub magazine backward.

Take out stuck staples that remain inside the opening

that staples are fired from as it appears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DST221 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info