Bedienungsanleitung Makita DTD154 (Seite 8 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

657995

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

8 ENGLISH

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.5: 1. Lamp

►Fig.6: 1. Button

Pulltheswitchtriggertoturnonthelamp.Toturnoff,

release it. The lamp goes out approximately 10 seconds

after releasing the switch trigger.

To keep the lamp off, turn off the lamp status. To turn off

thelampstatus,rstpullandreleasetheswitchtrigger.

Andthenpressthebutton

for one second within 10

seconds.

To turn on the lamp status again, press the button again

similarly.

NOTE:Toconrmthelampstatus,pullthetrigger.

Whenthelamplightsupbypullingtheswitchtrigger,

thelampstatusisON.Whenthelampdoesnotcome

on, the lamp status is OFF.

NOTE:Whenthetoolisoverheated,thelightashes

foroneminute,andthentheLEDdisplaygoesoff.In

this case, cool down the tool before operating again.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Reversing switch action

►Fig.7: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

Whenthereversingswitchleverisintheneutralposi-

tion, the switch trigger cannot be pulled.

Changing the impact force

►Fig.8: 1. Changed in four steps 2. Hard 3. Medium

4. Soft 5. T mode 6. Button

Youcanchangetheimpactforceinfoursteps:hard,medium,soft,andTmode.

This allows a tightening suitable to the work.

Everytimethebutton

is pressed, the number of blows changes in four steps.

“T” is a special mode for fastening self drilling screws. In this mode, the tool starts to drive a screw with faster rota-

tion, which is suited for drilling with the self-drilling-screw tip. Once the tool starts to tighten the screw, it impacts in

medium force grade.

For approximately one minute after releasing the switch trigger, the impact force can be changed.

Impact force grade displayed

on panel

Maximum blows Purpose Example of application

Hard

TS H

3,800 min

-1

(/min) Tightening when force and

speed are desired.

Tightening underwork mate-

rials, tightening long screws,

tightening bolts.

Medium

TS H

2,600 min

-1

(/min) Tighteningwhenagoodnish-

ing is needed.

Tighteningnishingboards,

plaster boards.

Soft

TS H

1,100 min

-1

(/min) Tightening with less force to

avoid screw thread breakage.

Tightening sash screws, tight-

ening small screws such as M6.

T mode

TS H

2,600 min

-1

(/min) Tightening when speed and

goodnishingareneeded.

Tightening self drilling screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD154 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info