Bedienungsanleitung Makita DTD155 (Seite 6 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691704

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

6 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery cartridge

rmly when installing or removing battery cartridge.

Failuretoholdthetoolandthebatterycartridgermlymay

cause them to slip off your hands and result in damage to

thetoolandbatterycartridgeandapersonalinjury.

►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthebatterycar-

tridge with the groove in the housing and slip it into place. Insert it all

the way until it locks in place with a little click. If you can see the red

indicator on the upper side of the button, it is not locked completely.

CAUTION:

Always install the battery cartridge fully

until the red indicator cannot be seen. If not, it may accidentally

falloutofthetool,causinginjurytoyouorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indicate the remain-

ingbatterycapacity.Theindicatorlampslightupforfewseconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

the tool off and stop the application that caused the tool

tobecomeoverloaded.Thenturnthetoolontorestart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetool/batterycool

before turning the tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

NOTE:Overheatprotection(forbattery)willworkonly

with batteries with star marking.

►Fig.3: 1. Star marking

Switch action

►Fig.4: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ing the switch trigger for about 6 minutes.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.5: 1. Lamp

►Fig.6: 1. Button

Pulltheswitchtriggertoturnonthelamp.Toturnoff,

releaseit.Thelampgoesoutapproximately10seconds

after releasing the switch trigger.

Tokeepthelampoff,turnoffthelampstatus.Toturnoffthe

lampstatus,rstpullandreleasetheswitchtrigger.And

then press the button for one second within 10 seconds.

Toturnonthelampstatusagain,pressthebuttonagain

similarly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTD155 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info