Bedienungsanleitung Makita DTP141 (Seite 9 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

600215

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Changing the torque setting (screwdriver

mode “ ”)

The fastening torque can be adjusted by pressing the

button in screwdriver mode.

The numbers on the LED display shows torque setting.

The fastening torque is minimum at the number 1 and

maximum at the number 9. The indication “P” is a special

mode for fastening self drilling screws.

Every time the button is pressed, the torque setting

changes from 1 to 9 and P, and then returns to 1.

The torque setting changes fast by keeping pressing the

button.

P mode is suitable for fastening self drilling screws into

steel plates in the following conditions.

• With speed change lever at “2” side, fastening max.

4 mm screw into total max. 3.2 mm steel plates.

• With speed change lever at “1” side, fastening max.

5 mm screw.

Before an actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

First, try to fasten the screw at “1”. Then increase the

number to continue fastening. Hold the tool firmly during

operation.

CAUTION:

• Don’t fasten the machine screw on P mode. It may

twist your wrist suddenly and result in personal injury.

NOTE:

• Make sure to check the number on LED display before

operation. If the number is not indicated, contact your

nearest Makita service center.

• When the remaining battery capacity gets low in the

screwdriver mode, the light flashes a few times when

fastening the screw completely. In this case, recharge

the battery. If you keep operating, you may not obtain

the desired torque.

• During pulling the switch trigger, the torque setting can-

not be changed.

• For approximately one minute after releasing the

switch trigger, the torque setting can be changed. If you

want to change the torque setting after that, pull the

switch trigger again.

• The number of torque setting does not mean specific

torque rate.

Empty signal for remaining battery capacity

(Fig. 11)

(Country specific)

The remaining battery capacity will be signaled on the

LED display when pulling the switch trigger.

The remaining battery capacity is shown as the following

table.

012273

NOTE:

• When the LED display goes off, the tool is turned off to

save the battery power. To check the remaining battery

capacity, slightly pull the switch trigger.

• The LED display goes off approximately one minute

after releasing the switch trigger.

• When the temperature of the tool gets high, the light

flashes once per second for one minute, and then the

LED display goes off. In this case, cool down the tool

before operation.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver/drill/socket bit

(Fig. 12)

Use only the driver/drill/socket bit shown in the figure. Do

not use any other driver/drill/socket bit.

For tool with shallow bit hole

006348

For tool with deep bit hole

011405

1. To install the bit, pull the sleeve and insert the bit into

the sleeve as far as it will go. Then release the

sleeve to secure the bit. (Fig. 13)

2. To install the bit, insert the bit-piece and bit into the

sleeve as far as it will go. The bit-piece should be

inserted into the sleeve with its pointed end facing

in. Then release the sleeve to secure the bit.

(Fig. 14)

LED indicator status Remaining battery capacity

About 50% or more

About 20% – 50%

About less than 20%

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for install-

ing the bit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DTP141 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info