Bedienungsanleitung Makita DTR181 (Seite 17 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

793624

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

17 ENGLISH

Main power switch

CAUTION:

When you turn the power on, never

bring your limbs or face close to the binding or rotat-

ing parts of the tool tip.

CAUTION: When the power is turned on,

never touch the binding or rotating parts of the

tool tip.

CAUTION:

Before inserting the battery cartridge,



and lock the trigger. If you insert the battery cartridge

while the switch trigger is being pulled, it may cause an

accident if the wire tying process is accidentally carried out.

Fig.3

When you press the power button, the power turns

on and the tying mode lamp lights up. In order for the



-

matically. When you press the power button again, the

󰀨

Fig.4: 1. Tying mode lamp 2. Power button

NOTE:

󰀨

switch trigger is not pulled for 10 minutes, the tool is auto-

󰀨

NOTE: To restart the tool, turn the power on again.

Mode switching button

When the power is turned on and the tying mode lamp

is lit, you can select the single actuation mode or the

continuous actuation mode via the mode switching but-

ton. When you turn the power on again, the tool starts in

the mode that was most recently selected.

Fig.5: 1. Mode switching button 2. Single actuation

mode 3. Continuous actuation mode

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: When not operating the tool,

depress the trigger-lock button from side to

lock the switch trigger in the OFF position.

Fig.6: 1. Switch trigger 2. Trigger-lock button

To prevent the switch trigger from accidentally pulled,

the trigger-lock button is provided. To start the tool,

depress the trigger-lock button from A side and pull the

switch trigger. Release the switch trigger to stop. After

use, press in the trigger-lock button from B side.

When you pull the switch trigger, the tool performs the next

sequential operations as follows, and the tool stops automatically.

1. Feed the wire.

2. Cut the wire.

3. The hook holds and twists the wire.

4. The hook returns to the original position.

Tying strength setting

CAUTION: Be sure to lock the trigger before

starting the adjustment. When you turn the power

on, never bring your limbs or face close to the

binding or rotating parts of the tool tip. Otherwise,



Fig.7





the display panel.

Fig.8: 1.2. Display

panel

󰀨

tying, check the twisted portion for breakage.

󰀨



again.



When the battery voltage drops below the required

level, the tool will stop operating, an error tone will

sound, and the number "4" will appear on the display

panel. The error tone will continue to sound until the

󰀨

NOTE: If the ambient temperature is extremely low,

the error tone may sound even when the battery

󰀩

ASSEMBLY

CAUTION: Always be sure that the tool is

󰀨

before carrying out any work on the tool.

Loading the tie wire (wire reel)

CAUTION: Before mounting or dismounting

tie wires and accessories, be sure to turn the

󰀨

cartridge. Failure to do so may cause an accident.

NOTICE: Using wires other than Makita's genu-

ine tie wires may cause the tool to malfunction.

1. Push the release lever, and lock it with the lock

lever.

Fig.9: 1. Release lever 2. Lock lever

When you push the release lever, a gap is created

between the left and right feed gears.

Fig.10: 1. Release lever 2. Lock lever 3. Feed gears

2. Open the reel cover.

Fig.11: 1. Reel cover

3. Mount the wire reel on the tool in the orientation



Fig.12: 1. Wire reel

Makita DTR181 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info