Bedienungsanleitung Makita DUC121 (Seite 18 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599988

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge.

Failure to hold the tool and the battery cartridge firmly

may cause them to slip off your hands and result in

damage to the tool and battery cartridge and a per-

sonal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the car-

tridge does not slide in easily, it is not being inserted

correctly.

Battery protection system (Lithium-ion battery

with star marking) (Fig. 2)

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically cuts

off power to the tool to extend battery life.

The tool will automatically stop during operation if the

tool and/or battery are placed under one of the following

conditions:

• Overloaded:

The tool is operated in a manner that causes it to

draw an abnormally high current.

In this situation, release the trigger switch on the tool

and stop the application that caused the tool to

become overloaded. Then pull the trigger switch

again to restart.

If the tool does not start, the battery is overheated.

In this situation, let the battery cool before pulling the

trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the

tool will not operate. In this situation, remove and

recharge the battery.

Switch action (Fig. 3)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing saw chain

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the saw chain.

• Always wear gloves when installing or removing the

saw chain.

• Use only saw chain and guide bar with bar tip designed

for this chain saw (see the Extract from the spare parts

list).

• In order to prevent kickback, do not remove the bar tip

or replace the guide bar with one without a bar tip.

Loosen the screw by turning counterclockwise the knob

until the sprocket cover comes off. (Fig. 4)

Remove the sprocket cover.

Remove saw chain and guide bar from the tool.

Fit in one end of the saw chain on the top of guide bar. At

this time, fit the saw chain as shown in the figure

because it rotates in the direction of arrow. (Fig. 5)

Place the saw chain so that the spring is positioned

inside it and fit in the other end of saw chain around the

sprocket as shown in the figure. (Fig. 6)

While turning the guide bar counterclockwise, install it so

that the end of guide bar contacts the spring. (Fig. 7)

Insert the hook of sprocket cover into the hole in the tool

and then place the sprocket cover on the tool. (Fig. 8)

Turn the knob clockwise to tighten the screw firmly.

(Fig. 9)

Adjusting saw chain tension (Fig. 10 & 11)

Just a slight loosening of the screw allows the saw chain

tension to be adjusted. After adjusting, retighten the

screw firmly.

CAUTION:

• For a while after a new saw chain is installed, it tends to

become loosened. From time to time check the saw

chain tension before use.

• Low tension of saw chain may cause coming out of

place.

• Installing or removing saw chain should be carried out

in a clean place free from sawdust and the like.

Spike bumper (optional accessory) (Fig. 12)

To install spike bumper, perform the following steps:

1. Remove the sprocket cover, saw chain and guide

bar as described in this instruction manual.

2. Fit the holes of spike bumper along with the holes on

the chainsaw.

3. Tighten them firmly with screws.

OPERATION

Lubrication (Fig. 13)

Saw chain is automatically lubricated when the tool is in

operation.

Check the amount of remaining oil in the oil tank through

the oil inspection window.

To refill the tank, remove the cap from the oil tank open-

ing.

Makita DUC121 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info