Bedienungsanleitung Makita DUC254C (Seite 13 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690906

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

13 ENGLISH

FUNCTIONAL DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.3: 1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

►Fig.4: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automati-

cally stops and the main power lamp blinks in green. In

this situation, turn the tool off and stop the application

thatcausedthetooltobecomeoverloaded.Thenturn

the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically and the main power lamp lights up in red.

In this case, let the tool and battery cool before turning

the tool on again.

NOTE: In high temperature environment, the over-

heat protection likely to work and the tool stops

automatically.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically and the main power lamp blinks in red. In

this case, remove the battery from the tool and charge

the battery.

Main power switch

WARNING: Always turn off the main power

switch when not in use.

Toturnonthetool,pressthemainpowerswitchuntil

themainpowerlamplightsupingreen.Toturnoff,

press the main power switch again.

►Fig.5: 1. Main power lamp 2. Main power switch

NOTE:Themainpowerlampblinksingreenifthe

switch trigger is pulled under unoperatable conditions.

Thelampblinksinoneofthefollowingconditions.

• Whenyouturnonthemainpowerswitchwhile

holding down the lock-off lever and the switch

trigger.

• Whenyoupulltheswitchtriggerwhilethechain

brake is applied.

• Whenyoureleasethechainbrakewhileholding

down the lock-off lever and pulling the switch

trigger.

NOTE:Thischainsawemploystheautopower-off

function.Toavoidunintentionalstartup,themain

power switch will automatically shut down when the

switch trigger is not pulled for a certain period after

the main power switch is turned on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC254C Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info