Bedienungsanleitung Makita DUC353 (Seite 14 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690908

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

14 ENGLISH

OPERATION

Lubrication

Saw chain is automatically lubricated when the tool is in

operation. Check the amount of remaining oil in the oil

tank periodically.

Torellthetank,laythechainsawonitssideand

remove the oil tank cap. The proper amount of oil is 200

ml.Afterrellingthetank,makesurethattheoiltank

cap is tightened securely.

►Fig.20: 1. Oil tank cap 2. Oil tank (translucent)

Afterrelling,holdthechainsawawayfromthe

tree. Start it and wait until lubrication on saw chain is

adequate.

►Fig.21

NOTICE: When lling the chain oil for the rst

time, or relling the tank after it has been com-

pletely emptied, add oil up to the bottom edge of

the ller neck. The oil delivery may otherwise be

impaired.

NOTICE: Use the saw chain oil exclusively for

Makita chain saws or equivalent oil available in

the market.

NOTICE: Never use oil including dust and parti-

cles or volatile oil.

NOTICE: When pruning trees, use botanical oil.

Mineral oil may harm trees.

NOTICE: Before the cutting operation, make sure

that the provided oil tank cap is screwed in place.

WORKING WITH THE CHAIN SAW

CAUTION: The rst time user should, as a

minimum practice, do cutting logs on a saw-horse

or cradle.

CAUTION: When sawing precut timber, use a

safe support (saw horse or cradle). Do not steady

the workpiece with your foot, and do not allow

anyone else to hold or steady it.

CAUTION: Secure round pieces against

rotation.

CAUTION: Keep all parts of the body away

from the saw chain when the motor is operating.

CAUTION: Hold the chain saw rmly with

both hands when the motor is running.

CAUTION: Do not overreach. Keep proper

footing and balance at all times.

NOTICE: Never toss or drop the tool.

NOTICE: Do not cover the vents of the tool.

Bring the bottom edge of the chain saw body into

contact with the branch to be cut before switching on.

Otherwise it may cause the guide bar to wobble, result-

ingininjurytooperator.Sawthewoodtobecutbyjust

moving it down by using the weight of the chain saw.

►Fig.22

If you cannot cut the timber right through with a single

stroke:

Applylightpressuretothehandleandcontinuesawing

anddrawthechainsawbackalittle;thenapplythe

spikebumperalittlelowerandnishthecutbyraising

the handle.

►Fig.23

Bucking

1. Rest the bottom edge of the chain saw body on

the wood to be cut.

►Fig.24

2. Withthesawchainrunning,sawintothewood

while using the rear handle to raise the saw and the

front one to guide it. Use the spike bumper as a pivot.

3. Continue the cut by applying slight pressure to

the front handle, easing the saw back slightly. Move

the spike bumper further down the timber and raise the

front handle again.

NOTICE: When making several cuts, switch the

chain saw off between cuts.

CAUTION: If the upper edge of the bar is used

for cutting, the chain saw may be deected in

your direction if the chain becomes trapped. For

this reason, cut with the lower edge, so that the

saw will be deected away from your body.

►Fig.25

Whenyoucutawoodundertension,cutthepressured

side(A)rst.Thenmakethenalcutfromthetensioned

side (B). This prevents the bar from becoming trapped.

►Fig.26

Limbing

CAUTION: Limbing may only be performed by

trained persons.Ahazardispresentedbytherisk

of kickback.

Whenlimbing,supportthechainsawonthetrunkif

possible. Do not cut with the tip of the bar, as this pres-

ents a risk of kickback.

Pay particular attention to branches under tension. Do

not cut unsupported branches from below.

Do not stand on the felled trunk when limbing.

Burrowing and parallel-to-grain cuts

CAUTION: Burrowing and parallel-to-grain

cuts may only be carried out by persons with

special training. The possibility of kickback presents

ariskofinjury.

Perform parallel-to-grain cuts at as shallow an angle as

possible. Take an extra caution when carrying out the

cut as the spike bumper cannot be used.

►Fig.27

Felling

CAUTION: Felling work may only be per-

formed by trained persons. The work is hazardous.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC353 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info