Bedienungsanleitung Makita DUC355 (Seite 16 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

695759

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

16 ENGLISH

Carrying tool

Before carrying the tool, always apply the chain brake

and remove the battery cartridges from the tool. Then

attach the guide bar cover. Also cover the battery car-

tridge with the battery cover.

►Fig.29: 1. Guide bar cover 2. Battery cover

MAINTENANCE

CAUTION:

Always be sure that the tool is

switched off and the battery cartridge is removed before

attempting to perform inspection or maintenance.

CAUTION: Always wear gloves when perform-

ing any inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Sharpening the saw chain

Sharpen the saw chain when:

•

Mealy sawdust is produced when damp wood is cut;

• Thechainpenetratesthewoodwithdifculty,even

when heavy pressure is applied;

• The cutting edge is obviously damaged;

• The saw pulls to the left or right in the wood.

(caused by uneven sharpening of the saw chain or

damage to one side only)

Sharpen the saw chain frequently but a little each time.

Twoorthreestrokeswithaleareusuallysufcientfor

routine resharpening. When the saw chain has been

resharpened several times, have it sharpened in our

authorized service center.

Sharpening criteria:

WARNING: An excessive distance between

the cutting edge and depth gauge increases the

risk of kickback.

►Fig.30: 1. Cutter length 2. Distance between cutting

edge and depth gauge 3. Minimum cutter

length (3 mm)

— All cutter length must be equal. Different cutter

lengths prevent the saw chain from running

smoothly and may cause the saw chain to break.

— Do not sharpen the chain when the cutter length

has reached 3 mm or shorter. The chain must be

replaced with new one.

—

The chip thickness is determined by the distance between

the depth gauge (round nose) and the cutting edge.

— The best cutting results are obtained with following

distance between cutting edge and depth gauge.

• Chainblade90PX:0.65mm(0.025″)

• Chainblade91PX:0.65mm(0.025″)

►Fig.31

— The sharpening angle of 30° must be the same on

all cutters. Different cutter angles cause the chain

to run roughly and unevenly, accelerate wear, and

lead to chain breaks.

— Useasuitableroundlesothatthepropersharp-

ening angle is kept against the teeth.

• Chain blade 90PX : 55°

• Chain blade 91PX : 55°

File and le guiding

— Useaspecialroundle(optionalaccessory)for

saw chains to sharpen the chain. Normal round

lesarenotsuitable.

— Diameteroftheroundleforeachsawchainisas

follows:

• Chainblade90PX:4.5mm(3/16″)

• Chainblade91PX:4.0mm(5/32″)

— Theleshouldonlyengagethecutteronthefor-

wardstroke.Lifttheleoffthecutteronthereturn

stroke.

— Sharpentheshortestcutterrst.Thenthelength

of this shortest cutter becomes the standard for all

other cutters on the saw chain.

— Guidetheleasshowninthegure.

►Fig.32: 1. File 2. Saw chain

—

Thelecanbeguidedmoreeasilyifaleholder

(optionalaccessory)isemployed.Theleholderhas

markings for the correct sharpening angle of 30° (align

the markings parallel to the saw chain) and limits the

depthofpenetration(to4/5ofthelediameter).

►Fig.33: 1. File holder

— After sharpening the chain, check the height of the

depth gauge using the chain gauge tool (optional

accessory).

►Fig.34

— Removeanyprojectingmaterial,howeversmall,

withaspecialatle(optionalaccessory).

— Round off the front of the depth gauge again.

Cleaning the guide bar

Chips and sawdust will build up in the guide bar groove.

Theymayclogthebargrooveandimpairtheoilow.

Clean out the chips and sawdust every time when you

sharpen or replace the saw chain.

►Fig.35

Cleaning the sprocket cover

Chips and saw dust will accumulate inside of the

sprocket cover. Remove the sprocket cover and saw

chain from the tool then clean the chips and saw dust.

►Fig.36

Cleaning the oil discharge hole

Small dust or particles may be built up in the oil dis-

charge hole during operation. These dust or particles

mayimpairtheoiltoowandcauseaninsufcient

lubrication on the whole saw chain. When a poor chain

oil delivery occurs at the top of guide bar, clean the oil

discharge hole as follows.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUC355 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info