Bedienungsanleitung Makita DUH601Z (Seite 12 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

711167

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

12 ENGLISH

NOTICE: Depending on the usage conditions,

the tool is automatically turned off without any

indication if the tool is overloaded by entangled

branches or debris. In this case, switch off the

tool and remove the battery cartridge, and then

remove entangled branches or debris using tools

such as pliers. After removing the branches or

debris, install the battery cartridge and turn on

the tool again.

Overheat protection for tool or battery

There are two types of overheating; tool overheating

and battery overheating. When the tool over heating

occurs, all speed indicators blink. When the battery over

heating occurs, indicator blinks.

If the overheating occurs, the tool stops automatically.

Let the tool and/or battery cool down before turning the

tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically and indicator blinks.

If the tool does not operate even when the switches are

operated, remove the battery from the tool and charge

the battery.

Angle setting of the handle

CAUTION: Always make sure that the handle

is locked in the desired position before operation.

CAUTION: Do not pull down the lever to

unlock the handle while pulling the switch trigger.

Do not pull the switch trigger while pulling down

the lever and turning the handle. Failure to do so

may cause a malfunction of the tool.

You can set the angle of the handle to 0°, 45°, or 90°

to the left or right. To change the angle of the handle,

turn the handle while pulling down the lever, and then

release the lever.

► Fig.3: 1. Lever

Power switch action

WARNING: For your safety, this tool is

equipped with lock-off lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply press the switch lever

and pull the switch trigger without pressing the

lock-off lever. Return the tool to our authorized

service center for proper repairs BEFORE further

usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-off lever.

WARNING: Before installing the battery car-

tridge on the tool, always check to see that the

switch trigger and switch lever actuate properly

and return to the "OFF" position when released.

Operating a tool with a switch that does not actuate

properly can lead to loss of control and serious per-

sonal injury.

CAUTION: Never put your nger on the

switch when carrying. The tool may start uninten-

tionally and cause injury.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-off lever. This can cause

switch breakage.

Press and hold the main power button to turn on the

tool. The power lamp lights up when the tool is turned

on. To turn off the tool, press and hold the main power

button again. The power lamp goes off when the tool is

turned off.

► Fig.4: 1. Power lamp 2. Main power button

NOTE: The tool is automatically turned off if the tool is

not operated for a certain period.

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool,

depress the lock-off lever, and then press the switch

lever and pull the switch trigger. The tool speed

increases by increasing pressure on the switch trigger.

Release the switch trigger to stop.

► Fig.5: 1. Switch lever 2. Lock-off lever 3. Switch

trigger

Speed adjusting

You can adjust the tool speed by tapping the main

power button.

Each time you tap the main power button, the level of

speed will change.

► Fig.6: 1. Power lamp 2. Main power button

Indicator Mode Stroke speed

High 4,400 min

-1

Medium 3,600 min

-1

Low 2,000 min

-1

Reverse button for debris removal

WARNING: If the entangled branches or

debris cannot be removed by the reverse func-

tion, switch off the tool and remove the bat-

tery cartridge, and then remove the entangled

branches or debris using tools such as pliers.

Failure to switch off the tool and remove the bat-

tery cartridge may result in serious personal injury

from accidental start-up. Removing the entangled

branches or debris by hand may cause an injury,

since the shear blades may move in reaction to

removing them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUH601Z Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info