Bedienungsanleitung Makita DUH752 (Seite 13 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690901

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

13 ENGLISH

This tool has a reverse button to change the direction

of shear blades movement. It is only for removing

branches and debris entangled in the tool.

To reverse the shear blades movement, tap the reverse

button when the shear blades have stopped, then press

the switch lever and pull the switch trigger while press-

ing the lock-off lever. The power lamp starts blinking,

and the shear blades move in reverse direction.

When entangled branches and debris are removed,

the tool returns to the regular movement and the power

lamp stops blinking and lights up.

► Fig.7: 1. Reverse button

NOTE:

If the entangled branches or debris cannot be removed,

release and pull the switch trigger until they are removed.

NOTE: If you tap the reverse button while the shear

blades are still moving, the tool comes to stop and to

be ready for reverse movement.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: When replacing the shear blades,

always wear gloves so that your hands do not

directly contact the blades.

NOTICE: When replacing the shear blades, do

not wipe off grease from the gear and crank.

Installing or removing the shear

blades

CAUTION: Attach the blade cover before

removing or installing the shear blades.

You can install 500 mm, 600 mm, or 750 mm shear

blades to your tool.

1. Place the tool upside down, and then remove 6

screws.

► Fig.8: 1. Screw

2. Remove the cover and the plate.

► Fig.9: 1. Cover 2. Plate

NOTE: The plate may remain on the cover.

3. Remove the rod.

► Fig.10: 1. Rod

NOTE: The rod may remain on the cover.

4. Remove 2 screws, the felt pad, the washers, and

the sleeves, and then remove the shear blades.

► Fig.11: 1. Felt pad 2. Screw 3. Washer 4. Sleeve

5. Shear blades

5. Remove the blade cover.

6. Attach the blade cover to the new shear blades.

7. Adjust the crank so that 2 holes are lined up on

the alignment line.

► Fig.12: 1. Hole 2. Alignment line

8. Align the protrusions on the shear blades vertically

at the same position.

► Fig.13: 1. Protrusion

9. Attach the felt pad to the shear blades.

► Fig.14: 1. Felt pad

10. Insert the protrusion on the shear blades to the

hole on the rod, then align the position of the felt pad

with the holes on the tool, and then attach new sleeves

and washers.

► Fig.15: 1. Protrusion 2. Hole 3. Felt pad 4. Washer

5. Sleeve

NOTICE: Apply a small amount of grease to the

inner periphery of the hole of the rod.

NOTICE: Be careful not to lose the washers and

the sleeves.

11. Align the holes on the shear blades with the holes

on the tool, and then tighten 2 screws to x the shear

blades.

► Fig.16: 1. Screw 2. Hole

12. Attach the rod.

► Fig.17: 1. Rod 2. Small hole

NOTICE: Apply a small amount of grease to the

inner periphery of the small hole of the rod.

NOTICE: Make sure that the protrusion on the

shear blades ts in the small hole on the rod.

13. Attach the plate.

► Fig.18: 1. Protrusion 2. Plate

NOTICE: Make sure that the protrusion on the

shear blades ts in the hole on the plate.

14. Attach the cover, and then tighten 6 screws.

► Fig.19: 1. Cover 2. Screw

NOTICE: Be sure to attach 2 long screws to the

center holes.

NOTICE: If the shear blades do not move

smoothly, the shear blades are not engaged with

the rods properly. Install the shear blades again.

NOTICE: If the parts other than the shear

blades such as the rods are worn out, ask Makita

Authorized Service Centers for parts replacement

or repairs.

Installing or removing the chip receiver

Optional accessory

CAUTION: When installing or removing the

chip receiver, always wear gloves so that your

hands do not directly contact the shear blades.

NOTICE: The blade cover cannot be installed if

the chip receiver is installed on the tool. Before

carrying or storing the tool, uninstall the chip

receiver, and then install the blade cover to avoid

blade exposure.

NOTICE: Be sure to remove the blade cover

before installing the chip receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUH752 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info