Bedienungsanleitung Makita DUM166 (Seite 13 von 29) (Deutsch, Englisch)

599978

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

• Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and

recharge the battery.

Indicating the remaining battery capacity

(Only for battery cartridges with “B” at the end of the

model number.) (Fig. 3)

Press the check button on the battery cartridge to indicate

the remaining battery capacity. The indicator lamps light

up for few seconds.

015658

NOTE:

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Switch action (Fig. 4)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop. The

lock-off button can be pressed from either right or left side.

Indication lamp (Fig. 5)

Running the tool allows the indication lamp to show the

battery cartridge capacity status.

When the tool is also overloaded and has stopped during

operation, the lamp lights up in red.

Refer to the following table for the status and action to be

taken for the indication lamp.

Note 1: The time at which the indication lamp lights up varies by the temperature around the work area and the battery

cartridge conditions.

010970

Adjusting the shearing height (Fig. 6)

Changing the position of holding the change lever allows

three-stepped setting for sheared grass height (10 mm,

20 mm, 30 mm).

To change setting, tilt the change lever for the base frame

position and with the change lever tilted move it up or

down along the tool surface until the protrusion on base

frame fits in one of the holes in the tool and release it.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing blade cover

CAUTION:

• Be careful not to contact the shear blade when

installing or removing the blade cover. Contacting the

shear blade may cause personal injuries. (Fig. 7 & 8)

Slide the blade cover from the tool’s side until the shear

blade completely hides itself and then push in it lightly

towards the tool from the front.

To remove the blade cover, take the above installation

procedure in reverse.

Installing or removing base frame

CAUTION:

• Before installing or removing base frame, be sure to

install the blade cover.

Indicator lamps

Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery may

have

malfunctioned.

Indication lamp Status Action to be taken

The lamp blinks in red. This indicates the appropriate time to

replace the battery cartridge when the

battery power becomes low.

Recharge the battery cartridge as soon

as possible.

The lamp lights up in red. (Note 1) This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Recharge the battery cartridge.

The lamp lights up in red. (Note 1) Autostop due to overload. Turn off the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUM166 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info