Bedienungsanleitung Makita DUR141 (Seite 9 von 22) (Englisch, Holländisch)

599972

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

10. Should the cutting tool hit stones or other hard

objects, immediately switch off the motor and

inspect the cutting tool.

11. Before commencing cutting, the cutting tool must

have reached full working speed.

12. During operation always hold the tool with both

hands. Never hold the tool with one hand during

use. Always ensure a safe footing.

13. All protective equipment such as guards supplied

with the tool must be used during operation.

14. Except in case of emergency, never drop or cast

the tool to the ground or this may severely

damage the tool.

15. Never drag the tool on the ground when moving

from place to place, the tool may become

damaged if moved in this manner.

16. Always remove the battery cartridge from the tool:

– whenever leaving the tool unattended;

– before clearing a blockage;

– before checking, cleaning or working on the

tool;

– before making any adjustments, changing

accessories or storing;

– whenever the tool starts vibrating unusually;

– whenever transporting the tool.

17. Don’t force the tool. It will do the job better and

with less likelihood of a risk of injury at the rate for

which it was designed.

Maintenance instructions

1. The condition of the cutting tool, protective

devices must be checked before commencing

work.

2. Turn off the motor and remove the battery

cartridge before carrying out maintenance,

replacing the cutting tool and cleaning the tool.

3. After use, disconnect the battery cartridge from

the tool and check for damage.

4. Check for loose fasteners and damaged parts

such as nearly halfway cut-off state in the cutting

tool.

5. When not in use store the equipment in a dry

location that is locked up or out of children’s

reach.

6. Use only the manufacturer’s recommended

replacement parts and accessories.

7. Always ensure that ventilation openings are kept

clear of debris.

8. Inspect and maintain the tool regularly, especially

before/after use. Have the tool repaired only by

our authorized service center.

9. Keep handles dry, clean and free from oil and

grease.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

IMPORTANT SAFETY

INSTRUCTIONS

ENC007-7

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

PARTS DESCRIPTION (Fig. 4)

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before adjusting or

checking function on the tool. Failure to switch off

and remove the battery cartridge may result in serious

personal injury from accidental start-up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUR141 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita DUR141

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info