Bedienungsanleitung Makita DUR187L (Seite 17 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690919

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

17 ENGLISH

MAINTENANCE

WARNING: Always be sure that the tool is

switched off and battery cartridge is removed

before attempting to perform inspection or main-

tenance on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injuryfromaccidentalstart-up.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Replacing the nylon cord

WARNING: Use nylon cord with diameter

specied in “SPECIFICATIONS” only. Never use

heavier line, metal wire, rope or the like. Use rec-

ommended nylon cord only, otherwise it may cause

damage to the tool and result in serious personal

injury.

WARNING: Make sure that the cover of the

nylon cutting head is secured to the housing

properly as described below. Failure to properly

secure the cover may cause the nylon cutting head to

yapartresultinginseriouspersonalinjury.

1. Press on the housing latches inward to lift off the

cover, then remove the spool.

►Fig.38: 1. Latch 2. Cover

2. Prepareapproximately3m(9ft)ofnewnylon

cord. Fold the new nylon cord with one end become

approximately80mm(3-1/8″)longerthantheother

end. Then hook the new nylon cord into the notch in the

center of the spool.

Windbothendsrmlyaroundthespoolinthedirection

of the head rotation (left-hand direction indicated by LH

on the side of the spool).

►Fig.39: 1.Spool

3. Windallbutabout100mm(3-15/16″)ofthe

cords, leaving the ends temporarily hooked through a

notch on the side of the spool.

►Fig.40

4. Mount the spool in the housing so that the grooves

and protrusions on the spool match up with those in the

housing. Keep the side with letters on the spool visible

on the top. Now, unhook the ends of the cord from their

temporary position and feed the cords through the

eyelets to come out of the housing.

►Fig.41: 1.Spool2. Housing 3.Eyelet

5. Align the protrusion on the underside of the cover

withtheslotsoftheeyelets.Thenpushthecoverrmly

onto the housing to secure it.

►Fig.42

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

TROUBLESHOOTING

Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual,

donotattempttodismantlethetool.Instead,askMakitaAuthorizedServiceCenters,alwaysusingMakitareplace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Motor does not run. Battery cartridge is not installed. Install the battery cartridge.

Battery problem (under voltage) Recharge the battery. If recharging is not effective,

replace battery.

The drive system does not work

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Motor stops running after a little use. Battery's charge level is low. Recharge the battery. If recharging is not effective,

replace battery.

Overheating. Stopusingoftooltoallowittocooldown.

ItdoesnotreachmaximumRPM. Battery is installed improperly. Install the battery cartridge as described in this

manual.

Battery power is dropping. Recharge the battery. If recharging is not effective,

replace battery.

The drive system does not work

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Cutting tool does not rotate:

stop the machine immediately!

Foreignobjectsuchasabranchis

jammedbetweentheguardandthe

nylon cutting head.

Removetheforeignobject.

The drive system does not work

correctly.

Askyourlocalauthorizedservicecenterforrepair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUR187L Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info