Bedienungsanleitung Makita DUT130 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

691284

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 ENGLISH

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.3: 1. Indicator lamps 2. Check button

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

mayhave

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placed under one of the following conditions:

Overload protection

Whenthetoolorbatteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetool

automaticallystopswithoutanyindication.Inthissit-

uation, turn the tool off and stop the application that

caused the tool to become overloaded. Then turn the

tool on to restart.

Overheat protection

Whenthetoolorbatteryisoverheated,thetoolstops

automatically.Inthiscase,letthetoolandbatterycool

before turning the tool on again.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically.Inthiscase,removethebatteryfromthe

toolandchargethebattery.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

CAUTION: Switch can be locked in "ON" posi-

tion for ease of operator comfort during extended

use. Apply caution when locking tool in "ON"

position and maintain rm grasp on tool.

CAUTION: Do not install the battery cartridge

with the lock button engaged.

CAUTION: When not operating the tool,

depress the trigger-lock button from side to

lock the switch trigger in the OFF position.

►Fig.4: 1. Trigger-lock button

►Fig.5: 1. Switch trigger 2. Lock button 3. Trigger-

lock button

Topreventtheswitchtriggerfromaccidentallypulled,

the trigger-lock button is provided. To start the tool,

depress the trigger-lock button from A (

) side and pull

theswitchtrigger.Toolspeedisincreasedbyincreas-

ing pressure on the switch trigger. Release the switch

trigger to stop. After use, depress the trigger-lock button

from B ( ) side.

For continuous operation, depress the lock button while

pulling the switch trigger, and then release the switch

trigger.Tostopthetool,pulltheswitchtriggerfully,then

release it.

Speed change

NOTICE: Use the speed change knob only after

the tool comes to a complete stop. Changing the

toolspeedbeforethetoolstopsmaydamagethetool.

NOTICE: Always set the speed change knob

carefully into the correct position.Ifyouoperate

the tool with the speed change knob positioned half-

waybetweentheposition1andtheposition2,the

toolmaybedamaged.

NOTICE: If the rotation speed signicantly

decreases during operation in the high speed

mode, stop the tool and change the mode to the

low speed mode.Otherwise,themotormayget

overloadedandcauseamalfunctionorre.

Two speed ranges can be preselected with the speed

change knob.

To change the speed, turn the speed change knob so

that the pointer points to the position 1 for low speed or

the position 2 for high speed.

►Fig.6: 1. Pointer 2. Speed change knob

Accidental restart preventive

function

Ifyouinstallthebatterycartridgewhilepullingthe

switch trigger or locking the switch trigger, the tool does

not start. To start the tool, release the switch trigger, and

then pull the switch trigger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DUT130 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info