Bedienungsanleitung Makita DVC340 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599963

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

4. Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the cleaner is switched off and the

battery cartridge is removed before adjusting or check-

ing function on the cleaner.

Installing or removing battery cartridge (Fig. 1)

CAUTION:

• Always switch off the cleaner before installing or remov-

ing of the battery cartridge.

• Hold the cleaner and the battery cartridge firmly

when installing or removing battery cartridge. Fail-

ure to hold the cleaner and the battery cartridge firmly

may cause them to slip off your hands and result in

damage to the cleaner and battery cartridge and a per-

sonal injury.

To remove the battery cartridge, slide it from the cleaner

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the cleaner, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the car-

tridge does not slide in easily, it is not being inserted

correctly.

Battery protection system

The cleaner is equipped with the protection system,

which automatically cuts off the output power for its long

service life.

The cleaner stops during operation when the cleaner

and/or battery are placed under the following situation.

This is caused by the activation of protection system and

does not show the cleaner trouble.

• When the cleaner is overloaded:

At this time, press the “OFF” button and remove

causes of overload and then press the “HIGH/LOW”

button again to restart.

• When battery cells get hot: (refer to the note below.)

If any operation of the “HIGH/LOW” button and the

“OFF” button, the motor will remain stopped. At this

time, stop use of the cleaner and cool or charge the

battery cartridge after removing it from the cleaner.

• When the remaining battery capacity gets low:

If any operation of the “HIGH/LOW” button and the

“OFF” button, the motor will remain stopped. At this

time, remove the battery cartridge from the cleaner

and charge it.

NOTE:

• This temperature-sensitive protection is applied only

when the cleaner is used with a battery cartridge with a

star mark. (Fig. 2)

Switch action (Fig. 3)

To start the cleaner, simply press the “HIGH/LOW” but-

ton. To switch off, press the “OFF” button. To change the

cleaner speed, press the “HIGH/LOW” button. The first

press on this button is for high speed and the second

press for low speed and then each press on this button

repeats the high/low speed cycle alternatively.

ASSEMBLY

CAUTION:

• Always be sure that the cleaner is switched off and the

battery cartridge is removed before carrying out any

work on the cleaner.

• Any work with the battery cartridge being installed on

the cleaner may cause a personal injury or damage to

the objects around the cleaner.

Installing dust bag (Fig. 4, 5, 6 & 7)

Hold the square section of the dust bag joint and fit the

pins inside the dust bag joint to the notches in the dust

outlet of the cleaner and then insert and turn it clockwise

all the way until it stops.

At this time, make sure that the fastener part on the dust

bag faces upward.

NOTE:

• When the dust bag joint and the ring inside the dust

bag come off, install as follows.

(1) Align the dust bag joint with the seam of the dust

bag and install it so that its protrusion faces

upward.

(2) Tighten the ring inside the dust bag firmly so that

the pins and the ring are positioned as shown in the

figure.

Installing the shoulder strap (Fig. 8)

Attach one end hook of the shoulder strap onto the ring

in the front of the cleaner and thrust the other end of the

strap through the band of the dust bag and then attach

the other end hook as shown in the figure.

Adjusting the shoulder strap (Fig. 9)

To adjust the length of the shoulder strap, pull it out to

your desired length and pull the strap in the direction of

arrow as shown in the figure.

Connecting the hose (Fig. 10)

CAUTION:

• Do not force the hose to bend it and/or stamp it.

Forcing and/or stamping the hose may cause deforma-

tion or damage to the hose.

• Do not pull the hose to carry the cleaner. Pulling the

hose may cause deformation or damage to the hose.

Insert the “A” end of the hose to the suction opening of

the cleaner and turn it clockwise all the way until it locks.

Attach the cuff on the “B” end of the hose and then con-

nect it to the dust outlet of an power tool.

Makita DVC340 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info