Bedienungsanleitung Makita DVC350 (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

599964

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Replacing the front cuff (Fig. 11)

Change the front cuff of the hose according to the dust

outlet size of a power tool you use.

To remove the front cuff, hold the hose and turn it coun-

terclockwise.

To mount the front cuff, turn it clockwise and then screw it

in until it stops.

OPERATION

WARNING:

• Do not use the shoulder strap when working in a high

place.

• When using the cleaner as a stationary cleaner, place it

on a flat and stable surface.

Vacuum cleaner (Fig. 12 & 13)

When using the cleaner as a portable cleaner, cross-

hanging the shoulder strap before the breast is difficult to

drop the cleaner.

NOTE:

• Long cut-off decorative paper that may be produced by

plaster board cutting work depending on the conditions

of workpiece to be cut and that may be stuffed inside

the hose may cause the hose suction blocking. When

this occurs, change the cutting depth setting of power

tool to deeper depth, which will relieve the hose suction

blocking.

CAUTION:

• When the dust bag is just new, dust may come out of its

surface. Using it a few times will minimize the dust leak

from the surface.

Operation of the cleaner with a nozzle or a dust

bag being installed

WARNING:

• Always be sure that the cleaner is switched off and

the battery cartridge is removed before installing or

removing the nozzle or any other attachment on the

cleaner. Failure to switch off and remove the battery

cartridge may result in serious personal injury.

NOTE:

• Before the blower mode operation immediately after

the cleaner mode operation, remove all remaining dust

from the cleaner due to possible blow out of dust.

Using as a blower (Fig. 14)

Install the nozzle onto the outlet (air vent) without fail.

To install the nozzle, fit the pin protruding from the inside

of nozzle to one of the cleaner notches and then turn the

nozzle clockwise securely.

To remove the nozzle, turn counterclockwise and pull it

out.

Direct the top point of the cleaner and then switch on.

Emptying the dust bag

WARNING:

• Always be sure that both the cleaner and a con-

nected power tool are switched off and the battery

cartridge is removed and the power tool, if corded

tool, is unplugged before installing or removing the

dust bag on the cleaner and emptying the dust bag

(made of cloth). Failure to switch off, remove the bat-

tery cartridge and unplug the connected power tool

may result in electric shock and serious personal injury.

• When the dust bag is about half full, remove the dust

bag from the cleaner and pull the fastener out. Empty

the dust bag of its contents, tapping it lightly so as to

remove particles adhering to the insides which might

hamper further collection.

NOTE:

• For the time to empty the dust bag, use a guide line

that the dust bag becomes full when drilling about

450 holes with 6.5 mm diameter and 40 mm depth

on the concrete. A dust bag clogged with the built up

particles may reduce the dust collection power and

cause damage to the cleaner motor.

CAUTION:

• Attach the dust bag (made of cloth) to the dust bag

joint securely and close the fastener completely

before use. Failure to attach the dust bag securely and

close its fastener completely may cause blow-out of

dust and result in serious personal injury.

Pick up the square section of the dust bag joint firmly,

turn it counterclockwise and then remove the dust bag.

(Fig. 15)

Open the fastener and dispose of the dust. (Fig. 16)

CAUTION:

• Remove all particles adhering to the fastener area.

MAINTENANCE

WARNING:

• Always be sure that the cleaner is switched off and the

battery cartridge is removed before attempting to per-

form inspection or maintenance.

Cleaning the filter area (Fig. 17)

CAUTION:

• Do not pick up materials other than dust, such as

stone, wood chip and the like since this cleaner is

intended for dust collection. Picking up stone, wood

chip and the like may cause damage to the fan and the

cleaner.

Check and clean up the filter area in the suction inlet reg-

ularly. Remove foreign objects which will obstruct suc-

tion.

Cleaning

From time to time wipe off the outside (cleaner body) of

the cleaner using a cloth dampened in soapy water.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita DVC350 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info