Bedienungsanleitung Makita dw 6702 (Seite 6 von 10) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

386595

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Reversing switch action (Fig. 7)

CAUTION:

•

Always check the direction of rotation before opera-

tion.

•

Use the reversing switch only after the machine

comes to a complete stop. Changing the direction of

rotation before the machine stops may damage the

machine.

This machine has a reversing switch to change the

direction of rotation. Slide the reversing switch up for

clockwise rotation or slide it down for counterclock-

wise rotation.

Overload protector

The overload protector automatically cuts out to break

the circuit whenever heavy work is prolonged. Wait

20 – 30 seconds before resuming operation.

Adjusting the fastening torque (Fig. 8)

The fastening torque can be adjusted infinitely from

approx. 20 kg·cm to 80 kg·cm. To adjust it, loosen the

two screws and turn the adjusting ring. Then tighten

the screws to secure the adjusting ring. Refer to the

table below for relation between the numbers on the

adjusting ring and the fastening torque to be obtained.

Numbers on

adjusting ring

Fastening torque to

be obtained

1 20 kg·cm

2 35 kg·cm

3 48 kg·cm

4 60 kg·cm

5 80 kg·cm

(Example)

35 kg·cm of fastening torque can be obtained when

the number 2 is aligned to the red mark.

NOTE:

•

Always tighten the two screws to secure the adjust-

ing ring after adjusting the fastening torque.

•

The fastening torque may differ depending upon the

kind of screws, the type of materials to be fastened,

etc. Before starting your job, always perform a test

operation to verify the adequate fastening torque.

Operation

The proper fastening torque may differ depending

upon the kind or size of screws, the type of materials

to be fastened, the condition of the threads, etc.

Before starting your job, always perform a test opera-

tion to verify adequate fastening torque.

Hold the machine firmly with both hands whenever

possible and place the socket over the bolt or nut.

Then turn the machine on. As soon as the bolt or nut

becomes tight, the clutch will cut in and the motor will

stop automatically. Release the switch trigger.

When fastening machine screws, use the proper

screwdriver bit shown in Fig. 9. It is commonly avail-

able on the market.

NOTE:

•

Always use the correct size socket for bolts and

nuts. An incorrect size socket will result in inaccu-

rate and inconsistent fastening torque and/or dam-

age to the bolt or nut.

•

Hold the machine with its square drive pointed

straight at the bolt or nut, or the bolt or nut will be

damaged.

•

If the motor will not start even after you pull the

trigger, release the trigger. Then pull the trigger

again after turning the socket slightly with your

fingers.

Fastening performance

The following reference table indicates the approximate fastening capacity from a single 1-hour battery charge.

It may differ under some conditions.

Screw size Fastening torque Fastenings

M6x14

5 About 800 screws

1 About 1,000 screws

MAINTENANCE

CAUTION:

Always be sure that the machine is switched off and

the battery cartridge is removed before carrying out

any work on the machine.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

Makita Authorized Service Center.

6702D (E) (’97. 9. 19)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita dw 6702 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info