Bedienungsanleitung Makita EA3600F (Seite 25 von 54) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690910

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Cleaning the cylinder space

CAUTION:

• Always wear eye protection.

After long period of operation, dust may accumulate in cylinder space. It may cause

overheating of the engine. Clean the cylinder space occasionally.

Perform cleaning as follows:

1. Open two hooks, and remove the cleaner cover.

2. Remove the air cleaner.

NOTE:

• During cleaning, cover the opening with a clean cloth to prevent dirt or foreign

materials from falling into the carburetor.

3. Remove three screws and remove the cylinder cover. It is easier to remove the

cylinder cover when the front hand guard is forward position.

4. Clean the cylinder space and cylinder ns. Use a brush or air compressor if

necessary.

5. Return the cylinder cover, air cleaner, and cleaner cover after cleaning.

Checking the screws on the mufer

Remove the cylinder cover and dust cover, and check the tightness of four screws

on the mufer. Tighten it if it is loose.

Checking the spark arrester

CAUTION:

• Do not start the engine if the spark arrester is damaged or missing.

The spark arrester prevents hot carbon from ying out of exhaust pipe. Check the

spark arrester regularly as following steps:

1. Remove the cylinder cover.

2. Remove the screw which secures the spark arrester. It is easier to remove the

screw by pushing the front hand guard forwards. Then slide the spark arrester.

Clean the spark arrester if necessary with a wire brush.

If the spark arrester is damaged, replace it.

Cleaning of parts

Always keep the engine clean by wiping down with a cloth rag.

Inspection of bolts, nuts and screws

- Check bolts, nuts, etc. Tighten them if necessary.

- Check the fuel cap and oil cap for tightness. Check for fuel leakage.

- Replace damaged parts with new ones for safety operation.

Storing tool

CAUTION:

• The engine is still hot just after stopping engine. When draining the fuel, allow

sufcient time for the engine to cool down after stopping it. Otherwise a skin burn

and/or re may result.

• When the machine is kept out of operation for a long time, drain all fuel from the

fuel tank and carburetor, and keep it at a dry and clean place.

Biologically degradable saw chain oil can only be kept for a limited period. Beyond

two years after manufacture, biological oils begin to acquire an adhesive quality,

and cause damage to the oil pump and components in the lubricating system.

- Before taking the chain saw out of service for a longer period, empty the oil tank

and ll it with a small quantity of engine oil (SAE 30).

- Run the chain saw briey to ush all residue of the biological oil out of the tank,

lubricating system and saw mechanism.

Store the chain saw on a suitable surface.

Before returning the chain saw to service, ll up with fresh bio-degradable saw

chain oil.

NOTE:

• When the chain saw is taken out of service, small quantities of chain oil leaks

from it for some time afterwards. This is normal, and is not a sign of a fault.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EA3600F Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info