Bedienungsanleitung Makita EA4300F (Seite 8 von 48) (Englisch)

599861

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

10 feet

Chain saw operating instructions

For assembly follow the procedure in the appropriate

section "Mounting Guide Bar and Chain" of this manual.

MAKITA chain, guide bar and sprocket must match each

other (see the appropriate section in this manual).

WARNING!

Proper tension of the chain is extremely impor-

tant. In order to avoid false setting the tensioning

procedure must be followed as described in this

manual. Always make sure the hexagonal nut(s)

for the sprocket guard is (are) tightened securely

after tensioning the chain. Check chain tension once

more after having tightened the nuts and thereafter

at regular intervals (always before starting to work).

If the chain becomes loose while cutting, shut off

the engine and then tighten. Never try to tighten

the chain while the engine is running!

Fueling

Your MAKITA saw uses on oil-gasoline mixture for fuel

(see chapter "Fuel" of this manual).

Wipe off any spilled fuel before starting your saw and

check for leakage.

Check for fuel leakage while refueling and during opera-

tion. If fuel or oil leakage is found, do not start or run

the engine until leak is xed and spilled fuel has been

wiped away. Clothing with fuel on it has to be changed

immediately (this is a danger to your life!).

Avoid skin contact with fuel. Never loosen or remove

the cap of the fuel tank while the engine is running.

Starting

Do not drop start. This method is very dangerous be-

cause you may lose control of the saw (g. 6).

WARNING!

Gasoline is an extremely ammable fuel. Use ex-

treme caution when handling gasoline or fuel mix.

Do not smoke or bring any sparks or ame near

the fuel (g. 5).

Fueling instructions

Fuel your chain saw in well ventilated areas or out-

doors. Always shut off the engine and allow it to cool

before refueling. Select bare ground for fueling and

move the chain saw at least 10 feet (3 m) from fueling

spot before starting the engine (g. 5a).

Place the chain saw on rm ground or other solid

surface in an open area. Maintain a good balance and

secure footing. Place your right foot through the rear

handle opening and rmly grasp the front handle with

your left hand (g. 6a).

Be absolutely sure that guide bar and chain are clear

of you or all other obstructions and objects, including

the ground, because when the engine starts in semi-

throttle position, engine speed will be fast enough for

the clutch to engage the sprocket and turn the chain

which may cause a kickback.

Never attempt to start the saw when the guide bar is

in a cut or kerf.

When you pull the starter grip, don’t wrap the starter

rope around your hands. Do not allow the grip to

snap back, but guide the starter rope slowly back to

permit the rope to rewind properly. Failure to follow

this procedure may result in injury to hand or ngers

and may damage the starter mechanism.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EA4300F Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EA4300F

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info