Bedienungsanleitung Makita EA5001P (Seite 36 von 80) (Englisch, Französisch)

690913

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Instructions for periodic maintenance

To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be per-

formed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the

prescribed maintenance work can lead to accidents!

The user of the chain saw must not perform maintenance work which is not described in the operator’s manual. All such work must

be carried out by a MAKITA service center.

Service, spare parts and guarantee

Maintenance and repair

The maintenance and repair of modern engines as well as all safety devices require qualied technical training and a special work-

shop equipped with special tools and testing devices.

Any work not described in this manual may be performed only by a MAKITA service center.

The MAKITA service centers have all the necessary equipment and skilled and experienced personnel, who can work out cost-effective

solutions and advise you in all matters.

Repair attempts by third parties or unauthorized persons will void all warranty claims.

Please contact your nearest service center.

General Chain saw Clean exterior, check for damage. In case of damage,

have repaired by a qualied service center immediately

Saw chain Sharpen regulary, replace in good time 30-31

Chain brake Have inspected regularly at an authorized service center

Guide bar Turn over to ensure even wear of bearing surfaces

Replace in good time 23, 32

Starter cable Check for damage. Replace if damaged. 36

Before each start Saw chain Inspect for damage and sharpness 30-31

Check chain tension 23

Guide bar Check for damage

Chain lubrication Functional check 26

Chain brake Functional check 28

Combination switch,

Safety locking button,

Throttle lever Functional check 27

Fuel/oil tank

cap Check for tightness and lekages

Every day Air lter Clean (several times daily if necessary) 34

Guide bar Check for damage, clean oil intake bore 32

Guide bar support Clean, in particular the oil guide groove 26, 32

Idle speed Check (chain must not run) 29

Every week Fan housing Clean to maintain good cooling air ow. 19, 37

Cylinder area Clean to maintain good cooling air ow. 37

Spark plug Check and replace if necessary 35

Mufer Check tightness of mounting, Check screws 35

Spark arrester screen Clean or replace if necessary 37

Chain guide Check 22

Screws and nuts Check their condition and that they are rmly secured.

Every 3 months Fuel lter Replace 37

Fuel, oil tanks Clean

Annually Chain saw Check at an authorized service center

Storage Chain saw Clean exterior, check for damage. In case of damage,

have repaired by a qualied service center immediately

Guide bar/chain Demount, clean and oil slightly

Clean the guide groove of the guide bar 32

Fuel, oil tanks Empty and clean

Carburetor Run empty

Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EA5001P Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EA5001P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info