448378
11
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
11
To meet the applicable safety provisions, only the tool/
protector combinations as indicated in the table must be used.
Be sure to use genuine MAKITA cutter blades or
nylon cutting head.
The cutter blade must be well polished, free of cracks or
breakage. If the cutter blade hits against a stone during
operation, stop the engine and check the blade immediately.
Polish or replace the cutter blade every three hours of operation.
If the nylon cutting head hits against a stone during operation,
stop the engine and check the nylon cutting head immediately.
CAUTION: The appropriate protector must always be installed, for
your own safety and in order to comply with accident-
prevention regulations.
Operation of the equipment without the guard being in
place is not permitted.
The outside diameter of the cutter blade must be
230 mm (9-1/16”). Never use any blades surpassing
230 mm (9-1/16”) in outside diameter.
Metal blade
Protector for metal blades
Nylon cutting head
Protector for
nylon cutting head
(3)
(2)
(1)
MOUNTING OF PROTECTOR
In use of the metal blade, x the protector (3) to the clamp (2) with two bolts
M6 x 30 (1).
NOTE: Tighten the right and left bolts evenly so that the gap between the clamp
(2) and the protector (3) will be constant.
Otherwise, the protector sometimes may not function as specied.
(3)
(4)
In cases where the nylon cord cutter is to be used, be sure to mount the
nylon cord cutter protector (4) onto the metal blade protector (3).
Mount the nylon cord cutter protector (4) by sliding it into place from the ank
of the metal blade protector (3) as shown.
Remove tape adhered to cutter, which cuts nylon cord, on nylon cord cutter
protector (4).
CAUTION: Be sure to push in nylon cord cutter protector (4) until it is fully
inserted.
Take care not to injure yourself on the cutter for cutting the nylon
cord.
To remove the nylon cord cutter protector (4), apply a hex wrench into the
notch on the metal blade protector (3), push it in and meanwhile slide the
nylon cord cutter protector (4).
Hex wrench
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Makita EBH253U wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Makita EBH253U

Makita EBH253U Bedienungsanleitung - Holländisch - 26 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info