Bedienungsanleitung Makita EBH341R (Seite 12 von 149) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448381

Zoom out

Zoom in

Vorherige Seite

1/149

Nächste Seite

MOUNTING OF HANDLE

–Fix a barrier to the left side of the machine together with the

handle for operator’s protection.

–Do not adjust position of the loop handle too close to the control

grip. Keep not less than 25cm distance between the handle

and the grip.

(a distance collar is provided for this purpose.)

MOUNTING OF PROTECTOR

To meet the applicable safety provisions, only the tool/protector

combinations as indicated in the table must be used. Failure to do

so may result in serious injury or death to user or bystanders.

Be sure to use genuine MAKITA cutter blade or nylon

cutting head.

–The cutter blade must be well clean, sharp and free of cracks

or breakage.

If the cutter blade contacts any hard objects or stones during

operation, stop the engine and check the blade immediately.

–Clean and sharpen or replace the cutter blade at least every

three hours of operation.

–The outside diameter of the cutter blade must not exceed 255

mm (10-1/32”). Never use any blades surpassing 255 mm (10-

1/32”) in outside diameter.

CAUTION : The appropriate guard must always be in-

stalled, for your own safety and in order to

comply with accident-prevention regulations.

Operation of the equipment without the

protector being properly in place must never

be attempted.

–Fix protector to a gear case by 4 bolts firmly

Never use a blush cutter without a protector or with a broken

protector.

MOUNTING OF CUTTER BLADE OR

NYLON CUTTING HEAD

Turn the machine upside down, and you can replace the cutter

blade or nylon cutting head easily.

Mounting of cutter blade

–Fit a cutting blade and other parts in the order as in the illustra-

tion. Thrust a bar or allen wrench into a hole of the gear case

until the cutting blade is locked and will not turn. Tighten a nut

by turning to counter-clockwise with a combination wrench.

(Note that the nut is tightened or loosened in the opposit

direction of a usual nut.)

–The nut must be re-tightened every time before use.

–For this brush cutter, we recommend the cutting attachments on

the right.

–Never attempt to cut a tree, a log, wood or other hard materials.

[Tightening torque: 28 – 48 N

࡮

NOTE : Always wear gloves when handling the cutter

blade.

Mounting of nylon cutting head

– The blade cap, bolt cover and nut are not necessary for

mounting the nylon cutting head. The nylon cutting head should

go on top of the grass cover.

– Insert the allen wrench through the hole in the gear case and

rotate the blade holder until it is locked with the alln wrench.

– Then screw the nylon cutting head onto the shaft by turning it

counter-clockwise.

– Remove the allen wrench.

Star Blade

Protector for metal

blades

Eddy Blade

PART NO.

6418501400

PART NO.

6418501900

PART NO.

6118502000

Nut

Bolt cover

Blade cap

Blade

Grass cover

Blade holder

Protector plate

Protector

Gear case

PART NO.6348003000 PART NO.174345800

Nylon cutting head

to engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EBH341R Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info