Bedienungsanleitung Makita EG241A (Seite 22 von 49) (Englisch, Holländisch)

448384

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

8. ”HOW-TO” MAINTENANCE

CAUTION

Make sure the engine is stopped before starting

any maintenance, servicing or repair.

NOTE

It is recommended to use ear protection when

performing operation, maintenance and repair of

the generator set.

ENGINE OIL CHANGE (See Fig. 󱌶-①)

■

Change engine oil every 100 hours.

(For new engine, change oil after 20 hours.)

(a) Drain oil by removing the drain plug and the oil ﬁ ller

cap while the engine is warm.

❶ OIL DRAIN PLUG

(b) Reinstall the drain plug and ﬁ ll the engine with oil

until it reaches the upper level on the oil ﬁ ller cap.

■

Use fresh and high quality lubricating oil to

the speciﬁ ed level as directed on page 5. If

contaminated or deteriorated oil is used or the

quantity of the engine oil is not sufﬁ cient, the

engine damage will result and its life will be greatly

shortened.

SERVICING THE AIR CLEANER

(See Fig. 󱌶-② thru ④)

Maintaining an air cleaner in proper condition is very

important.

Dirt induced through improperly installed, improperly

serviced or inadequate elements damages and wears

out engines. Keep the element always clean.

❶ BASE

❷ ELEMENT

❸ AIR CLEANER COVER

❹ BOLT

(a) Remove the bolt of air cleaner cover.

(EG601A, EG601AE, EG671A, EG671AE)

(See Fig.󱌶-④)

Remove the air cleaner cover and cleaner element.

(b) Urethane form : Wash urethane form element in

kerosene or diesel fuel.

Then saturate the element in a mixture of 3 parts

kerosene or diesel fuel and 1 part engine oil.

Squeeze the element to remove the mixture and

install it in the air cleaner.

NOTE

Instead of washing oil (kerosene), it is possible to

wash the urethane foam element in a solution of

mild detergent and warm water.

Then rinse the element thoroughly in clean water.

Allow the element to dry thoroughly.

Soak the element

in clean engine oil and squeeze out excess oil.

CLEANING AND ADJUSTING SPARK PLUG

(See Fig. 󱌶-⑤)

(a) If the plug is contaminated with carbon, remove it

using a plug cleaner or wire brush.

(b) Adjust the electrode gap to 0.6 to 0.7 mm.

Spark plug : BR-6HS (NGK)

CLEANING FUEL STRAINER

(See Fig. 󱌶-⑥)

Dirt and water in the fuel are removed by the fuel

strainer.

(a) Remove the strainer cup and throw away water

and dirt.

(b) Clean the screen and strainer cup with gasoline.

avoid fuel leak.

CHECKING CARBON BRUSH

Brush Maintenance Essentials

(Effective Length)

The brush is the area which touches the slip ring, and

its surface must be kept smooth.

If it is not smooth then carbon and other substances

will adhere between the brush and slip ring.

This must be buffed with sandpaper or the like

because it is hazardous.

The usable length of the brush is 5~11mm, so if the

brush is 5mm long or less replace it with a new one.

(See Fig.󱌶-⑦)

❶ LENGTH WHEN NEW

❷ EFFECTIVE BRUSH LENGTH

EG671A_en_GU6838.indd 14 2010/01/18 17:14:24

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EG241A Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EG241A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info