Bedienungsanleitung Makita EG241A (Seite 24 von 49) (Deutsch)

448384

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

9. PERIODIC OPERATION

AND INSPECTION

10. TRANSPORTING

Brush Maintenance Essentials

(Disassembly and Assembly) (See Fig. - )

BRUSH

SLIP RING

BRUSH HOLDER

FLANGE BOLTS

BRACKET COVER

FLANGE BOLTS

Disassembly

1. Remove the two  ange bolts (M5 x 20), then

remove the bracket cover.

2. Remove the two  ange bolts (M5 x 16), then

remove the brush.

Assembly

1. While pressing the brush against the slip ring,

secure it (1.5~2N•m) by tightening it with the two

 ange bolts (M5 × 16).

When doing so, con rm that the brush is in the

proper position relative to the slip ring.

2. Secure the bracket cover (3~4N•m) by tightening it

with the two  ange bolts (M5 × 20).

When furnishing the generator as emergency electric

power source, periodic operation and inspection are

needed.

Fuel (gasoline) and engine oil will be deteriorated with

time, and this causes that the engine is dif cult to start

and as the results improper engine operation and fault.

CAUTION

Since the fuel (gasoline) will be deteriorated

with time, replace fuel (gasoline) with fresh one

periodically; once every three (3) months is

recommended.

When transporting the generator, make sure that the

fuel (gasoline) should be drained from the tank.

WARNING



To prevent fuel spillage due to the vibration

and impact, never transport the generator

with the fuel (gasoline)  lled in the tank.



Secure the tank cap thoroughly.



To avoid the risk of the gasoline  ammability,

never leave the generator in an area exposed

to direct sunlight or high temperatures for a

long time.



Keep the fuel (gasoline) in the exclusive

gasoline storage tank made by steel when

transporting.

(a) Turn the engine switch to the “STOP” position.

(b) Drain the fuel from the tank.

CAUTION



Do not place any heavy objects on the

generator.



Select and place the generator in the proper

position of the transport vehicle so that the

generator not be moved or fallen down.

Fix the generator with rope as necessary.

This is done because if the length of the brush gets

any shorter, its contact pressure with the slip ring will

decrease, resulting in a drop in generator ef ciency

and the output voltage.

Check the brush every 500 hours to con rm its length.

In addition, check the brush length if the generator

malfunctions, such as when it is not generating power

or its voltage is low.

(a) Check the fuel (gasoline), engine oil and air

cleaner.

(b) Start engine.

engine for over ten minutes.

(d) Check for the following items;



Proper engine running.



Adequate output and the indicator lamp turned on

properly.



The engine switch normally operated.



No leakage of engine oil and fuel (gasoline).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EG241A Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EG241A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info