Bedienungsanleitung Makita EG4550A (Seite 15 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

599871

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

WARNING:

Contact with a hot engine or exhaust system can

result in serious burns or fire. Allow the engine cool

before transporting or storing the generator.

When transporting the generator, take care not to drop or

strike the generator. Do not place heavy objects on the

generator.

When transporting the generator on a vehicle, secure to

the generator frame as shown.

TROUBLESHOOTING

When the engine fails to start:

If the engine still fails to start, take the generator to an

authorized Makita generator dealer.

When no electricity is generated at the AC

receptacles:

TECHNICAL INFORMATION

Emission Control System Information

Source of Emissions

Carbon monoxide, oxides of nitrogen, and hydrocarbons

are produced in the combustion process. Controlling the

emission of hydrocarbons and oxides of nitrogen is

extremely important because, under certain conditions,

they react to form photochemical smog when subjected to

sunlight. Although carbon monoxide does not react in the

same way, it is toxic.

Makita utilizes the appropriate air-fuel ratios and other

emissions control systems in order to reduce the

emissions of carbon monoxide, oxides of nitrogen, and

hydrocarbons.

Furthermore, Makita fuel systems utilize components and

control technologies in order to reduce evaporative

emissions.

Tampering and Altering

The level of emissions may increase beyond the legal

limit, if the emission control system is tampered with or

altered. Acts that constitute tampering include:

• Removal or alteration of any part of the intake, fuel, or

exhaust systems.

• Altering or defeating the governor linkage or speed-

adjusting mechanism to cause the engine to operate

outside its design parameters.

Problems That May Affect Emissions

If you become aware of any of the following symptoms,

have the engine inspected and repaired by your servicing

dealer.

• Hard starting or stalling after starting.

• Rough idle.

• Misfiring or backfiring under load.

• Afterburning (backfiring).

• Black exhaust smoke or high fuel consumption.

Replacement Parts

The emission control systems on your Makita engine were

designed, built, and certified to conform to applicable

emission regulations. Therefore, it is recommended that

genuine Makita parts be used whenever you have

maintenance done. Since these original-design

replacement parts are manufactured to the same

standards as the original parts, their performance is

reliable. Using replacement parts that are not of the

original design and quality may decrease the

effectiveness of the emission control system.

Note that manufacturers producing aftermarket parts

assume the responsibility that the part will not adversely

affect emission performance. The manufacturer or

rebuilder of the part must certify that the engine will still

comply with emission regulations even with the use of the

part.

Maintenance

Follow the Maintenance Schedule. Remember that this

schedule is based on the assumption that the machine will

be used for the purpose it is designed. The machine will

require more frequent service for continuous high-load or

high-temperature operation, or use in unusually wet or

dusty conditions.

Check if fuel is in

the tank.

If empty, refill the fuel

tank.

Check the fuel

level.

Å Æ

If low, add the

recommended oil.

Check the

condition of the

spark plug.

Å Æ

If in bad condition,

readjust the gap and dry

the spark plug. Replace if

necessary.

Check if fuel is

reaching the

carburetor.

Å Æ

If not, clean the fuel

sediment cup.

Check that the

AC circuit

breaker is in the

“I (ON)” position.

Å Æ

If not, turn on the AC

circuit breaker.

Check if the

electrical

appliance or

equipment has

any defects.

Å Æ

If there are no defects,

take the generator to an

authorized Makita

generator dealer.

If there are defects:

- Replace the electrical

appliance or

equipment.

- Take the electrical

appliance or equipment

to an electrical shop to

be repaired.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EG4550A Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info