Bedienungsanleitung Makita EG6050A (Seite 9 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

599873

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Oil Alert System (Fig. 14)

The engine can be damaged if there is an insufficient

amount of oil in the crankcase. The Oil Alert system

prevents this from happening by automatically stopping

the engine before the oil level in the crankcase falls below

the safe limit (the engine switch will remain in the “I (ON)”

position). When the oil alert system works, the oil level

warning lamp lights up in red. The oil level should always

be checked before each use, regardless of this Oil Alert

system.

If the engine stops and fails to restart, check the engine oil

level before troubleshooting in other areas.

NOTICE:

When the amount of oil in the crankcase is sufficient, the

pilot lamp lights up in green. When the amount of oil is

insufficient, the oil level warning lamp lights up in red. Be

sure to add oil before using the generator.

AC Circuit Breaker (Fig. 10)

The AC circuit breaker automatically turns off if there is a

short circuit or a significant overload of the generator at

the receptacle. If the AC circuit breaker is turns off

automatically, make sure that the appliance is working

correctly and does not exceed the rated load capacity of

the circuit before turning on the AC circuit breaker again.

The AC circuit breaker may be used to turn the generator

power on or off.

AC Circuit Protector (EG4550A, EG5550A,

EG6050A only) (Fig. 11)

The AC circuit protectors automatically turn off if there is a

short circuit or a significant overload of the generator at

the 26A 230V. If an AC circuit protector turns off

automatically, make sure that the appliance is working

correctly and does not exceed the rated load capacity of

the circuit before resetting the AC circuit protector on.

GENERATOR USE

Connections to a Building’s Electrical

System

A qualified electrician must make the connections for

standby power to a building’s electrical system. Make sure

that the connection isolates the generator power from the

utility power, and complies with all applicable laws and

electrical codes. A transfer switch, which isolates

generator power from utility power, can be purchased

through authorized Makita generator dealers.

WARNING:

Electrical current from the generator may backfeed

into the utility lines if connections to a building’s

electrical system are made improperly. Such backfeed

may electrocute utility company workers or others

who come into contact with the lines during a power

outage, and the generator may explode, burn, or

cause fires when the utility power is restored. Consult

the utility company or a qualified electrician.

Ground System

Makita portable generators are equipped with a system

ground that connects generator frame components to the

ground terminals in the AC output receptacles. Since the

system ground is not connected to the AC neutral wire, if

the generator is tested by a receptacle tester, it will show

the same ground circuit condition as for a home

receptacle.

AC Applications

Before connecting an appliance or power cord to the

generator:

• Make sure that it is in good working condition. Faulty

appliances or power cords can cause electrical shock.

• If an appliance begins to operate in an abnormal

manner, becomes slow, or stops suddenly, turn it off

immediately. Disconnect the appliance, and determine

whether there is a problem with the appliance or if the

rated load capacity of the generator has been

exceeded.

• Make sure that the electrical rating of the tool or

appliance does not exceed the generator’s rating.

Never exceed the maximum power rating of the

generator. Power levels between rated and maximum

may be used for no more than one hour.

NOTICE:

Substantial overloading will turn off the circuit breaker.

Exceeding the time limit for maximum power operation or

slightly overloading the generator may not turn off the

circuit breaker or circuit protector, but will shorten the

service life of the generator.

Limit operation requiring maximum power to one hour.

Maximum power is as follows:

EG2250A: 2.2 kW

EG2850A: 2.8 kW

EG4550A: 4.5 kW

EG5550A: 5.5 kW

EG6050A: 6.0 kW

For continuous operation, do not exceed the rated power.

Rated power is as follows:

EG2250A: 2.0 kW

EG2850A: 2.6 kW

EG4550A: 4.0 kW

EG5550A: 5.0 kW

EG6050A: 5.5 kW

The total power requirements (VA) of all appliances

connected to the generator must be considered. Rating

information for appliances and power tools are usually

listed near the model number or serial number.

AC Operation (Fig. 12)

1. Start the engine.

2. Turn on the AC circuit breaker.

3. Plug in the appliance.

NOTICE:

Before connecting any appliance to the generator, make

sure they are in good working condition. If an appliance

begins to operate in an abnormal manner, becomes slow,

or stops suddenly, turn off the ignition switch lever

immediately. Then disconnect the appliance and check for

signs of malfunction.

Most motorized appliances require more than their rated

power for startup.

Do not exceed the current limit specified for any one

receptacle. If an overloaded circuit causes the AC circuit

breaker or AC circuit protector to turn off, reduce the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EG6050A Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info