Bedienungsanleitung Makita EG671A (Seite 18 von 49) (Englisch, Holländisch)

448391

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Battery Charging Procedures :

1) Stop engine.

2) Remove all connections from battery.

3) Insert the plug of exclusive DC cable into DC

receptacle.

4) Connect positive (red) clip of DC cable to positive

(+) terminal on battery, and then connect negative

(black) clip of DC cable to negative (-) terminal on

battery.

5) Take out all plugs at the battery electrolyte ﬂ uid

ﬁ ller ports.

6) Check the electrolyte ﬂ uid level, and reﬁ ll the

distilled water as necessary.

7) Start engine.

8) Make sure that the pilot lamp is turned on.

9) Make sure that the DC circuit breaker is in the ON

position.

10) Battery charging will be started.

CAUTION

■

Do not use both AC and DC output at the same

time.

■

Install correct positive (red) or negative (black)

cable to the correct polarity on the battery.

■

Connect and disconnect DC cable with engine

stopped.

■

An explosive hydrogen gas is discharged

through vent holes in the battery during the

charging process.

Do not allow spark or open ﬂ ame around

the generator or battery during the charging

process.

■

Electrolyte ﬂ uid contains sulphuric acid, and

so the ﬂ uid can burn eyes and clothing. Be

extremely careful to avoid contact.

If injured, wash the affected area immediately

with large quantities of water and consult a

doctor for treatment.

■

Charging time is varied according to the kind

of battery and discharged level of battery.

Measure the speciﬁ c gravity of electrolyte ﬂ uid

by means of hydrometer every one hour during

battery charging.

Make sure if the DC circuit breaker is not

turned off.

Battery charging is completed when the

speciﬁ c gravity is in the range of 1.26 to 1.28.

3. STOPPING THE GENERATOR

(a) Turn off the power switch of the electric equipment

and unplug the cord from receptacle of the

generator.

(b) Allow the engine about 3 minutes to cool down at

no-load before stopping.

Turn the engine switch to the position “ 〇 ” (OFF).

(See Fig.󱌴-⑥)

❶ “ ¦ ” (ON)

❷ “ 〇 ” (OFF)

[Electric starter model]

Turn the key switch to the STOP position.

(See Fig.󱌴-⑦)

❶ “ 〇 ” (STOP)

❷ “ ¦ ” (RUN)

❸ “

” (START)

(d) Close the fuel valve. (See Fig.󱌴-⑧)

❶ OPEN

❷ CLOSE

4. OIL SENSOR (See Fig. 󱌴-⑨)

❶ OIL SENSOR

(a) The oil sensor detects the fall in oil level in the

crankcase and automati-cally stops the engine

when the oil level falls below a predetermined level.

(b) When engine has stopped automatically, switch off

generator’s AC circuit breaker, and check the oil

level.

Reﬁ ll engine oil to the upper level as instructed on

page 5 and restart the engine.

procedures, check the oil level.

EG671A_en_GU6838.indd 10 2010/01/18 17:14:23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EG671A Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EG671A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info