Bedienungsanleitung Makita EH5000W (Seite 12 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

448393

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

- Never operate the hedge trimmer with a loose grip.

- Never touch the cutting blades when starting the engine and during operation.

- Operate the hedge trimmer in such a manner as to avoid inhalation of the

exhaust gases. Never run the engine in enclosed rooms (Risk of gas poisoning).

Carbon monoxide is an odorless gas.

- All protective equipment such as a guard supplied with the machine must be used

during operation.

- Never operate the engine if the mufﬂer is faulty or missing.

- Use the hedge trimmer only in good light and visibility.

- During the winter season beware of slippery or wet areas, ice and snow. (Risk of

slipping.) Always ensure a safe footing.

- Never stand on a ladder and run the hedge trimmer. Keep both feet on the

ground.

- Never climb up the trees with the hedge trimmer to perform cutting operation.

- Never work on unstable surfaces.

- Remove sand, stone, nails, wire, etc. found within the working area. Foreign

objects may damage the cutting blades.

- Prior to the cutting operation, cut away 8 mm or thicker branches with pruning

shears.

- Before commencing cutting, the cutting blades must have reached full working

speed.

- Always hold the hedge trimmer ﬁrmly with both hands on the handles.

- Use a ﬁrm grip with thumbs and ﬁngers encircling the handles.

- When you release the throttle, it takes a few moments before the cutting blades

stop.

- Do not operate the hedge trimmer with high idle speed. You cannot adjust the

cutting speed with the throttle control if the idle speed is too high.

- During the cutting operation, hold the hedge trimmer so that the blades form a

15-30° angle with the cutting line.

- Pay special attention when cutting hedges close to or against wire fences.

- Do not touch hard objects such as wire fence, stone or ground with the cutter

blades. It may cause blades to crack, chip or break.

- Should the cutting blades hit stones or other hard objects, immediately switch off

the engine and inspect the cutting blades for damage. Replace damaged blades

before re-commencing work.

- Take a rest periodically. Makita recommends to take a 10- to 20-minute rest every

50 minutes of use.

- Switch off the engine immediately in case of any engine problems.

- Operate the hedge trimmer with as little noise and contamination as possible. In

particular check the correct setting of the carburetor and the fuel/oil ratio.

- Never attempt to remove jammed cut material when blades are running. Put unit

down, turn it off, and remove necessary cuttings.

The rear handle can be turned down to 90° to the left or right side and set at every

45°.

To change the angle:

1. Press the release lever to release the lock.

2. Turn the handle to an angle of 0°, 45° or 90°.

3. Make sure that the release lever returns to the original position to engage the

lock.

Do not pull the throttle lever while the lock is released.

Do not release the lock during operation.

OPERATION OF THE MACHINE

ADJUSTING REAR HANDLE ANGLE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EH5000W Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EH5000W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info