Bedienungsanleitung Makita EK7300 (Seite 31 von 68) (Englisch, Französisch)

599876

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Troubleshooting

Guarantee

MAKITA guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting

from material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular

guarantee conditions may exist. If you have any questions, please contact your salesman, who is responsible for the guarantee of

the product.

Please note that we cannot accept any responsibility for damage caused by:

• Disregard of the operator’s manual.

• Non-performance of the required maintenance and cleaning.

• Incorrect carburetor adjustment.

• Normal wear and tear.

• Obvious overloading due to permanent exceeding of the upper performance limits.

• The use of other than original MAKITA cutting discs.

• Use of force, improper use, misuse or accidents.

• Damage from overheating due to dirt on the fan housing.

• Work on the Power Cut by unskilled persons or inappropriate repairs.

• Use of unsuitable spare parts or parts which are not original MAKITA parts, insofar as they have caused the damage.

• Use of unsuitable or old oil.

• Damage related to conditions arising from lease or rent contracts.

• Damages caused by disregarding loose outer bolted connections.

Cleaning, servicing and adjustment work is not covered by the guarantee. All repairs covered by the guarantee must be performed

by a MAKITA service center.

Malfunction System

Observation Cause

Cutting disc does not

start turning Clutch Engine runs Damage to clutch

Cutting disc runs in idle Carburetor, Cutting disc runs Incorrect idle speed,

clutch blocked clutch

Engine does not start or Ignition system Ignition spark Malfunction in fuel supply system, com-

only with difculty pression system, mechanical malfunction.

No ignition spark Switch on STOP, fault or short-circuit in the

wiring, plug cap or spark plug defective.

Fuel supply Fuel tank is lled Choke in wrong position, carburetor defective,

suction head dirty, fuel line bent or interrupted.

Compression Inside Cylinder base packing ring defective, radial

system shaft packings defective, cylinder or piston rings

defective

Outside Spark plug does not seal.

Mechanical Starter does not engage Spring in starter broken, broken parts

malfunction inside the engine.

Warm start difculties Carburetor Fuel tank is lled Wrong carburetor adjustment.

Ignition spark

Engine starts, but Fuel supply Fuel tank is lled Wrong idling adjustment, suction head or

dies immediately carburetor dirty.

Tank venting defective, fuel line interrupted,

cable defective, STOP switch defective.

Decompression valve dirty

Insufcient power Several systems Engine is idling Air lter dirty, wrong carburetor adjustment,

may be involved mufer clogged, exhaust channel in cylinder

simultaneously clogged, spark arrester screen clogged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EK7300 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EK7300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info