Bedienungsanleitung Makita EK7301 (Seite 23 von 68) (Englisch, Französisch)

599877

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Pre-lter (foam with air-lter oil)

Only for models DPC8131 and 8132

Clean or replace (when cutting with high dust amounts):

• Daily

or at least every

• 4 operating hours, or

• 8 tank llings, or

• 8 litres fuel mixture.

Clean or replace (when cutting wet, or when cutting steel):

• weekly

or at least every

• 25 operating hours, or

• 50 tank llings, or

• 55 litres fuel mixture.

Cleaning: Cleaning: Rinse off coarse dirt in running water.

Knead a capful MAKITA lter cleaner (Order No. 980 008 627

into the foam material of the pre-lter (1, Order No. 395 173

090) until it suds up well.

Rinse out pre-lter thoroughly in running water.

Let the pre-lter dry thoroughly.

In order to ensure full ltration effectiveness, air-lter

oil must be used with the pre-lter. Wet the pre-lter

with a capful (about 20 ccm) of MAKITA air-lter oil

(Order No. 980 008 628, biodegradable).

Knead the pre-lter to evenly distribute the oil. Then

squeeze out any excess oil.

NOTE: If using other air-lter oils, follow the manufacturer’s

instructions.

If cleaning is not possible on-site, have spare pre-lters on

hand (Order No. 395 173 090).

To insert the pre-lter in the lter cover, position it so it ts the

space in the cover and then press it in (5). The pre-lter must

t completely and cover all parts of the lter space, without

leaving any spaces unltered.

Inner lters (all models)

Wash out the dirty inner lter (3, Order No. 395 173 020)

in lukewarm soapy water with regular dishwashing liquid or

MAKITA lter cleaner (Order No. 980 008 627).

Let the inner lter dry thoroughly.

Air lter insert (paper cartridge, all models)

The air lter insert (2, Order No. 395 173 010) lters the intake

air through a very ne paper lter lamella system. For the rea-

son the cartridge must never be washed. Clean the air lter

insert once a week.

To clean the air lter insert, spread it out slightly and carefully

tap it against a clean surface.

Replace the air lter insert every 100 operating hours. Replace

it immediately if there is a drop in power, drop in speed, or

smoke in the exhaust.

Before installing the lter system, check the intake opening to

make sure no dirt particles have fallen in. If they have, remove

them.

CAUTION: Turn off the engine before cleaning the air lter! Never clean out the air lter with compressed air! Do

not clean the pre-lter and inner lter with fuel.

The service life of the engine depends on the condition and regular maintenance of the lter elements. Failure to

perform maintenance and cleaning at the prescribed intervals will cause increased wear inside the engine!

If the air lter becomes damaged, replace immediately! Pieces of cloth or large dirt particles can destroy the engine!

Do not work in dusty conditions when it can be avoided! The ne dust generated when dry-cutting concrete and stone

is hazardous to the health of the operator and also shortens the service life of the engine. Whenever possible, wet-cut

with water when working in concrete and stone, to bind the dust.

Pre-lter (dry foam)

Only for models EK7300, 7301

If the pre-lter (1, Order No. 395 173 080) is dirty, wash

it out in lukewarm water with standard dishwashing liquid

or MAKITA lter cleaner (Order No. 980 008 627). If using

MAKITA lter cleaner, proceed as described after the text

section "Cleaning".

Let the pre-lter dry thoroughly.

NOTE: The pre-lter must be cleaned daily, or several times

daily if working under dusty conditions. If cleaning is not

possible on-site, have spare pre-lters on hand. Replace the

pre-lter at least every 25 operating hours.

To improve ltration effectiveness, the pre-lter can be wet-

ted with air-lter oil. Before adding air-lter oil, carefully

wash the lter with air-lter cleaner. Care for the oiled air

lter as described for DPC8131, 8132.

To insert the pre-lter in the lter cover, position it so it ts

the space in the cover and then press it in (5). The pre-lter

must t completely and cover all parts of the lter space,

without leaving any spaces unltered.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EK7301 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EK7301

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info