Bedienungsanleitung Makita EK8100 (Seite 7 von 68) (Englisch, Französisch)

599881

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

min. 5 m

● Maintenance

● Refuelling

● Changing cutoff discs

● Repositioning the

cutting attachment

● Stopping work

● Transport

● Putting out of function

Cutoff discs

- The protection hood must always be on! Change discs only

with the engine off!

- There are two basic types of cutoff discs:

- For metal (hot cutting)

- For masonry (cold cutting)

WARNING!

Never use carbide tipped, circular saw blades or any kind of wood

cutting blades. Never cut any type of wood. Reactive forces can

cause severe personal injury from blade contact or thrown tips.

NOTE: When using diamond cutoff discs, always make sure to observe

the "direction of rotation" markings. Diamond discs should only be

used for cutting masonry/brick/ concrete etc.

- Cutoff discs are intended only for radial loading, i.e. for cutting. Do

not grind with the sides of the cutting disc! This will break the disc

(10)!

Caution!

Never change direction (turning radius less than 5 meters (16

feet), exert lateral (sideways) pressure, or tip the Power Cut dur-

ing cutting (11)!

- Use a cutting disc only for cutting the materials it is intended for. The

proper type of disc must be used, for either metals or masonry.

- The arbor hole of the cutting disc must be an exact t with the arbor

or shaft. If the arbor hole is larger, it must be tted with an adapter

ring (available as an accessory).

The cutting disc must be rated for freehand cutting at up to 3850

rpm or 80 m/sec for 400 mm discs, 4370 rpm or 80 m/sec for 350

mm discs, or up to 5100 rpm or 80 m/s for 300 mm discs. Use only

cutting discs that comply with EN 12413, EN 13236.

- The disc must be free of defects (12). Do not use defective cutting

discs.

Always tighten the cutting disc mounting bolt to a torque of 30

Nm. Otherwise, the cutting disc can twist.

- Before starting the cutting disc, make sure you have a steady foot

ing.

- Put the Power Cut into operation only as described in this operator’s

manual (13). Always place your left foot in the rear handle and grasp

the other handle rmly (with thumb and ngers). Other starting

methods are not allowed.

- When starting the Power Cut it must be well supported and securely

held. The cutting disc must not be touching anything.

- If the cutting disc is new, test it by running it at least 60 seconds at

top speed. When doing this, make sure that no persons or body parts

are in the extended swing range of the disc, in case it is defective

and ies apart.

When working with the Power Cut always hold it with both

hands. Take the back handle with the right hand and the tubular

handle with the left hand. Hold the handles tightly with your thumbs

facing your ngers.

CAUTION: When you release the throttle lever the disc will

keep spinning for a short period of time (free-wheeling effect).

- Continuously ensure that you have a safe footing.

Hold the Power Cut such that you will not breathe in the

exhaust gas. Do not work in closed rooms or in deep holes

or ditches (danger of poisoning by fumes).

WARNING – CARBON MONOXIDE PRODUCED DURING USE

CAN KILL – DO NOT USE POWER CUTTER INDOORS – MAKE

SURE THERE IS PROPER VENTILATION WHEN USING POWER

CUTTER IN TRENCHES OR OTHER CONFINED SPACES.

Switch off the Power Cut immediately if you observe any

changes in its operating behavior.

Switch off the engine before inspecting the V-belt tension or

tightening it, replacing the cutting wheel, repositioning the cutter

attachment (side or middle position) or eliminating faults (14).

- Turn off the engine immediately and check the disc if you hear or

feel any change in cutting behaviour.

- Turn off the Power Cut when taking a break or stopping work (14).

Place the unit in such a way that the disc is not touching anything

and cannot endanger anyone.

- Do not put the overheated Power Cut in dry grass or on any inam

mable objects. The mufer is very hot (danger of re).

IMPORTANT: After wet cutting, rst turn off the water feed and then

let the disc run at least 30 seconds, to ing off the remaining water

and prevent corrosion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EK8100 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EK8100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info