Bedienungsanleitung Makita EM2600L (Seite 12 von 38) (Englisch, Holländisch)

599888

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

Handling fuel

Utmost care is required when handling fuel. Fuel may contain substances similar

to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel

vapors, and avoid any contact of fuel or oil with your skin.

Mineral oil products degrease your skin. Prolonged skin contact with these

products will cause your skin to become extremely dry, which may result in

various kinds of skin disease. In addition, allergic reactions may occur.

Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately

wash them with clear water. If your eyes are still irritated, see a doctor

immediately.

Fuel and oil mixture

The brush cutter engine is a high-efficiency two-stroke engine. It runs on a

mixture of fuel and two-stroke engine oil. The engine is designed for unleaded

regular fuel with a min. octane value of 91 RON.

To obtain optimum engine performance and to protect your health and the

environment, use only unleaded fuel!

To lubricate the engine, add two-stroke engine oil (quality grade: JASO FC or

ISO EGD) to the fuel. The engine has been designed to use the specified two-

stroke engine oil at mixture ratio of 50:1 to protect the environment.

Additionally, long service life accompanied by reliable operation and minimum

emissions are guaranteed through the use of this mixture ratio. Reliable

functioning of the brush cutter cannot be guaranteed unless this mixture ratio of

50:1 (specified 2-stroke engine oil) is strictly observed.

Correct mixture ratio:

Gasoline: Specified two-stroke engine oil = 50 : 1 or

Gasoline: Other manufacturer’s two-stroke engine oil = 25 : 1 recommended

NOTE: To prepare the fuel-oil mixture, first mix the entire oil quantity with half of

the fuel required, then add the remaining fuel. Thoroughly shake the

mixture before pouring it into the brush cutter tank. To ensure safe

operation, do not add more engine oil than the specified amount. Doing

so will only result in a higher production of combustion residues which

pollute the environment and clog the exhaust channel in the cylinder as

well as the muffler. In addition, the fuel consumption will rise and the

performance will decrease.

Refuelling

The engine must be switched off.

– Thoroughly clean the area around the fuel filler cap (2) to prevent dirt from

getting into the fuel tank (1).

– Unscrew the fuel filler cap (2) and fill the tank with fuel.

– Tightly screw on the fuel filler cap (2).

– Clean the screw fuel filler cap (2) and tank after refueling.

Storage of Fuel

Fuel cannot be stored for an unlimited period of time.

Purchase only the quantity required for a 4-week operating period. Only use

approved fuel storage containers.

Fuel/Refuelling

Observe the Safety Instructions on page 3.

20 cm

40 cm

100 cm

200 cm

400 cm

1,000 cm

(1 liter)

5,000 cm

(5 liter)

10,000 cm

(10 liter)

50:1 25:1

Gasoline

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM2600L Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EM2600L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info