Bedienungsanleitung Makita EM2650UH (Seite 18 von 48) (Englisch, Holländisch)

448396

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

CAUTION: The cutting tools mentioned below must only be resharpened by an

authorized facility. Manual resharpening will result in imbalances of

the cutting tool causing vibrations and damage to the equipment.

– cutter blade

An expert resharpening and balancing service is provided by Authorized

Service Agents.

NOTE: To increase the service life of the cutter blade it may be turned over

once, until both cutting edges have become blunt.

RESHARPENING THE CUTTING TOOL

ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)

When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw.

CHECKUP OF LOW-SPEED ROTATION

– Set the low-speed rotation to 3,000 min

-1

If it is necessary to change the rotation speed, regulate the adjusting screw

(illustrated on the right), with Phillips screwdriver.

– Turn the adjusting screw to the right, and the engine rotation will increase.

Turn the adjusting screw to the left, and the engine rotation will drop.

– The carburetor is generally adjusted before shipment. If it is necessary to

readjust it, please contact Authorized Service Agent.

Carburetor

Adjusting

screw

NYLON CUTTING HEAD

The nylon cutting head is a dual string trimmer head capable of both automatic

and bump & feed mechanisms.

The nylon cutting head will automatically feed out the proper length of nylon

cord by the changes in centrifugal force caused by increasing or decreasing

rpms. However, to cut soft grass more efciently, bump the nylon cutting head

against the ground to feed out extra cord as indicated under operation section.

Operation

– Increase the nylon cutting head speed to approx. 6,000 min

-1

Low speed (under 4,800 min

-1

) is not suitable, the nylon cord will not feed out

properly at low speed.

– The most effective cutting area is shown by the shaded area.

If the nylon cord does not feed out automatically proceed as follows:

1. Release the throttle lever to run the engine idle and then squeeze the

throttle lever fully. Repeat this procedure until the nylon cord feeds out to

the proper length.

2. If the nylon cord is too short to feed out automatically with the above

procedure, bump the knob of the nylon cutting head against the ground to

feed out the nylon cord.

3. If the nylon cord does not feed out with procedure 2, rewind/replace the

nylon cord by following the procedures described under “Replacing the

nylon cord.”

Most effective cutting area

Idle speed

Full speed

Knob

STOPPING

1) Release the throttle lever (2) fully, and when the

engine rpm has lowered, set the I-O switch to

STOP the engine will now stop.

2) Be aware that the cutting head may not stop

immediately and allow it to slow down fully.

EM2650LH

EM2651LH

EM2650UH

EM2651UH

STOP

(1)

(2)

STOP

(1)

(2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM2650UH Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EM2650UH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info