Bedienungsanleitung Makita EM2653LHN (Seite 26 von 84) (Englisch, Portugiesisch, Spanisch)

690574

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

WARNING: When draining the fuel, be sure to stop the engine and conrm that the engine cools

down.

Just after stopping the engine, it may still hot with possibility of burns, inammability

and re.

ATTENTION: When the machine is kept out of operation for a long time, drain up all fuel from the

fuel tank and carburetor, and keep it at a dry and clean place.

Fault location

– Drain up fuel from the fuel tank and carburetor according to the following

procedure:

1) Remove the fuel tank cap, and drain fuel completely.

If there is any foreign matter remaining in the fuel tank, remove it

completely.

2)Pulloutthefuellterfromtherellportusingawire.

3) Push the primer pump until fuel is drained from there, and drain fuel

coming into the fuel tank.

4)Resettheltertothefueltank,andsecurelytightenthefueltankcap.

5) Then, continue to operate the engine until it stops.

– Remove the spark plug, and drip several drops of engine oil through the

spark plug hole.

– Gently pull the starter handle so that engine oil will spread over the engine,

and attach the spark plug.

– Attach the cover to the cutter blade.

– Ingeneral,storethemachineinhorizontalposition,orifitisnotpossible,

place the machine as the engine comes below the cutting tool. Otherwise

engine oil may leak from inside. Pay full attention how to store the machine to

preventthemachinefromfalling.Otherwiseitmayresultinpersonalinjury.

– Keep the drained fuel in a special container in a well-ventilated shade.

Drain fuel

Humidity

STORAGE

Attention after long-time storage

– Before startup after long-time shutdown, be sure to replace oil (refer to P 19). Oil will deteriorate while the machine is kept out of

operation.

Fault System Observation Cause

Engine not starting or with

difculty

Ignition system Ignition spark O.K. Fault in fuel supply or compression system, mechanical

defect

No ignition spark STOP-switch operated, wiring fault or short circuit, spark

plug or connector defective, ignition module faulty

Fuel supply Fueltanklled Incorrect choke position, carburetor defective, fuel supply

line bent or blocked, fuel dirty

Compression No compression when

pulled over

Cylinder bottom gasket defective, crankshaft seals

damaged, cylinder or piston rings defective or improper

sealing of spark plug

Mechanical fault Starter not engaging Broken starter spring, broken parts inside of the engine

Warm start problems Tanklledignitionspark

existing

Carburetor contaminated, have it cleaned

Engine starts but dies Fuel supply Tanklled Incorrectidlingadjustment,carburetorcontaminated

Fuel tank vent defective, fuel supply line interrupted,

cable or STOP-switch faulty

Insufcientperformance Several systems may

simultaneously be

affected

Engine idling poor Airltercontaminated,carburetorcontaminated,mufer

clogged, exhaust duct in the cylinder clogged

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM2653LHN Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info