Bedienungsanleitung Makita EM4350LH (Seite 22 von 54) (Englisch, Holländisch)

599894

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

CAUTION: Before doing any work on the equipment, always stop the engine and pull the plug cap off the spark plug (see “checking the spark

plug”).

Always wear protective gloves!

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

Daily checkup and maintenance

Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the metal blade or nylon –

cutting head.

Before operation, always check for clogging of the cooling air passage and the cylinder ns. –

Clean them if necessary.

Perform the following work daily after use: –

Clean the equipment externally and inspect for damage.•

Clean the air lter. When working under extremely dusty conditions, clean the lter the several times a day.•

Check the blade or the nylon cutting head for damage and make sure it is rmly mounted.•

Check that there is sufcient difference between idling and engagement speed to ensure that the cutting tool is at a standstill while the •

engine is idling (if necessary reduce idling speed).

If under idling conditions the tool should still continue to run, consult your nearest Authorized Service Agent.

Check the functioning of the I-O switch, the lock-off lever, the throttle lever, and the lock button. –

SERVICING INSTRUCTIONS

REPLACEMENT OF ENGINE OIL

Deteriorated engine oil will shorten the life of the engine. Be sure to check the oil and level regularly.

WARNING:

The engine and engine oil is still hot just after stopping engine. Allow sufcient time for the engine and engine oil to cool

down. Otherwise a skin burn may result.

NOTE: If the oil lled above the limit, it may be contaminated or may catch re with white smoke. Allow sufcient time after stopping

engine for the engine oil to return to the oil tank to ensure accurate reading of the oil level.

Interval of replacement: After rst 20 operating hours, followed by every 50 operating hours.

Recommended oil: SAE10W-30 oil of API Classication SF Class or higher (4-stroke engine oil for automobile)

In replacement, perform the following procedure.

1) Make sure that the fuel tank cap is tightened securely.

2) Place large container (pan, etc.) under drain hole.

3) Remove drain bolt and then remove oil cap to drain out oil from drain hole.

At this time, be sure not to lose drain bolt’s gasket, or get dirty any of the

removed components.

4) Once all the oil has been drained, install gasket and drain bolt, and tightly

secure drain bolt, so that it will not loosen and cause leaks.

[Tightening torque: 5 N-m]

* Use cloth to fully wipe off any oil attached to bolt and equipment.

Oil cap

Drain bolt

Gasket

Drain hole

Alternative draining method

Remove oil cap, tilt the equipment toward oil ller hole, and drain out oil.

Collect oil in container.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM4350LH Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EM4350LH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info