Bedienungsanleitung Makita EM4350UH (Seite 23 von 54) (Deutsch, Englisch)

599893

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

5) Set the engine level, and gradually ﬁll up to upper limit mark with new oil.

6) After ﬁlling, tightly secure oil cap, so that it will not loosen and cause leaks.

If oil cap is not tightly secured, it may leak.

CLEANING OF AIR CLEANER

WARNING: Shut off the engine, keep away from open ﬂames

and do not smoke.

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

Turn the choke lever to the full close side, and keep the carburetor off from –

dust or dirt.

Removing air cleaner cover

Release the hook on the air cleaner cover by pressing down the loop on the –

plate.

Loosen ﬁxing bolt. –

Pull and remove the air cleaner cover. –

Cleaning element

Remove the elements and tap them to remove dirt. –

For heavy contamination: –

1) Remove the element (sponge), immerse it in warm water or in water-

diluted neutral detergent, and dry it completely. Do not squeeze or rub it

when washing.

2) Clean the element (paper) by tapping it gently. If you can use an air blow

gun, blow the compressed air onto the inside of the element (paper). Do

not wash the element (paper).

Before attaching the element (sponge), be sure to dry it completely. –

Insufﬁcient drying of the element (sponge) may lead to difﬁcult start-up.

Wipe out oil adhering around the air cleaner cover and separator plate with –

waste cloth.

Attaching air cleaner cover

Fit the element (sponge) and element (paper). Insert the element (sponge) all –

the way into the air cleaner cover.

Insert the side hook onto the air cleaner cover as illustrated, and push the –

lower part of the air cleaner cover until it clicks so that the hook sits into the

loop properly. And then tighten the air cleaner cover with ﬁxing bolt.

NOTICE:

Clean the elements several times a day, if excessive dust adheres to it. –

Dirty elements reduce engine power and make starting engine difﬁcult.

Remove oil on the elements. If operation continues with the elements –

remaining not cleared of oil, oil in the air cleaner may fall outside, resulting

in contamination of the environment.

Do not put the elements on the ground or dirty place. Otherwise they pick –

up dirt or debris and it may damage the engine.

Never use fuel for cleaning the elements. Fuel may damage them. –

Plate

Element (sponge)

Air cleaner cover

Element (sponge)

Separator plate

Element (paper)

Loop

Fixing bolt

POINTS ON OIL

Never discard replaced engine oil in garbage, earth or sewage ditch. –

Disposal of oil is regulated by law. In disposal, always follow the relevant

laws and regulations. For any points remaining unknown, contact

Authorized Service Agent.

Oil will deteriorate even when it is kept unused. Perform inspection and –

replacement at regular intervals (replace with new oil every 6 months).

Side hook

Hook

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EM4350UH Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EM4350UH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info