Bedienungsanleitung Makita EN4951SH (Seite 16 von 50) (Deutsch, Englisch)

599897

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

- Do not touch the cutting blade portion of the pole hedge trimmer during operation,

or when the engine is running.

- Take extra care not to inhale exhaust gases when working with the pole hedge

trimmer. Never operate the pole hedge trimmer in an enclosed room or an area



carbon monoxide is an odorless gas that is, it cannot be detected by the sense of

smell.

- Always wear adequate protective wear before starting to work with the pole

hedge trimmer.

- 

- Only use the pole hedge trimmer in good light and visibility conditions.

- Do not operate the pole hedge trimmer in darkness or fog. Beware of slippery and

wet areas (ice and snow) during the cold season (danger of slipping), and always

ensure secure footing.

- Never use the pole hedge trimmer while standing on an unstable surface or a

steep slope.

- Never use the pole hedge trimmer while standing on a ladder.

- Never climb a tree to use the pole hedge trimmer from the tree.

- Continuously check the working area for wires, cord, glass or other foreign

objects that could get caught in the cutting blades.

- Make sure that the cutting blades are in rapid motion before starting to cut.

- 

when working with the machine.

- To assure optimal control over the pole hedge trimmer, always completely wrap

your hands around the handles (use your thumb for counter pressure) and apply



- Note that the cutting blades will remain in motion for up to two seconds after the

throttle lever has been released.

- Do not cut with the pole hedge trimmer at low engine speed.

- The speed of the cutting blades cannot be adjusted properly with the throttle lever

when the engine is running at low speed.

- 

15° - 30° in the cutting direction and keep the pole hedge trimmer in a horizontal

position. Then start trimming the hedge using a swinging movement, much like

drawing circle segments with the hedge trimmer shaft.

- To trim the sides of a hedge, align the blades parallel to the surface to be cut and

start trimming with semi-circular upward (down-up) movements.

- Pay attention when trimming a hedge close to or against wire fences.

- Do not touch hard objects such as wire fence, stone or ground with the cutting

blades. It may cause blades to crack, chip or break.

- Do not use the pole hedge trimmer over an extended period of time. As a general

rule, for every 50 minutes of operation take a 10-20 minutes rest.

- If the cutting blades come into contact with stones or other solid objects, stop

the engine immediately and check the blades for damage. Replace the blades if

damaged.

- If the pole hedge trimmer develops a problem during operation (strange noises,

vibration, etc.), immediately stop the engine. Do not use the machine again until

the problem has been recognized and solved.

- Always do your utmost to keep pollution and noise emissions as low as possible

when operating the pole hedge trimmer. Pay special attention to correct

carburetor adjustment.

- If thick branches get jammed in the cutting blades, immediately stop the engine,

lay the equipment on the ground and remove the obstruction. Check the blades

for damage before using the machine again.

OPERATING THE POLE HEDGE TRIMMER

EN4950H

EN4951SH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EN4951SH Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita EN4951SH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info