Bedienungsanleitung Makita EW2051H (Seite 9 von 32) (Alle Sprachen)

690620

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

PRE-OPERATION FOR STARTING

(See Fig. )

1. CONNECT SUCTION HOSE (See Fig. - )

Use a reinforced-wall or wire braided hose to prevent

suction collapse. Since the pump self-priming time is

directly proportional to hose length, a short hose is

recommended.

CAUTION

Always use a strainer with the suction hose.

Gravel or debris sucked into the pump will

cause serious damage to the impeller and

the pump casing.

2. CONNECT DELIVERY HOSE (See Fig. - )

When using a fabric hose, always use a hose band

to prevent the hose from disconnecting under high

pressure.

3. CHECK ENGINE OIL (See Fig. - )

Before checking or relling engine oil, be sure the

engine is located on stable, level surface and stopped.

■

Do not screw the oil gauge into the oil ller neck

to check oil level. If the oil level is low, rell to the

upper level with the following recommended oil.

■

Use 4-stroke automotive detergent oil of API

service class SE or higher grade (SG, SH or SJ is

recommended).

■

Select the viscosity based on the air temperature at

the time of operation as shown in the table.

(See Fig.

- )

Explanation of Fig. -

Oil Gauge Upper Level

Lower Level

Model Oil capacity

EW2050H

EW3050H

EW2051H

EW3051H

0.6 L

4. CHECK FUEL (See Fig. - )

WARNING

■

Do not refuel while smoking, near an open

ame or other such potential re hazards.

Otherwise re accident may occur.

■

Remove the statistic electricity from your

body before relling the gasoline.

Sparking from electrostatic discharge may

cause the ignition to the vaporized fuel

(gasoline) resulting burns.

Static electricity can be discharged from the

body by touching by hand the metal parts of

the unit and the fuel dispensing pump.

NOTE

THIS ENGINE IS CERTIFIED TO OPERATE

ON AUTOMOTIVE UNLEADED GASOLINE.

■

Stop the engine and open the cap.

■

Use automotive unleaded gasoline only.

● Unleaded regular/premium or reformulated

gasoline containing no more than 10% Ethanol

(E10), or 15% MTBE may also be used.

● Never use gasoline containing ethanol exceeding

10%, or MTBE exceeding 15% because engine

or fuel system damage could result.

● Never use stale or contaminated gasoline.

● Use of these non-recommended fuels may result

in reduced performance and/or denial of warranty.

Fuel Tank Capacity

Model

Fuel Tank capacity

Litre (U.S.gal)

EW2050H

EW3050H

EW2051H

EW3051H

3.2 (0.85)

■

Close the fuel valve before lling the fuel tank.

■

Do not ll above the top of the fuel lter screen

(marked

), or the fuel may overow when it heats

up later and expands.

Explanation of Fig. -

Maximum Fuel level

■

When lling the fuel tank, always use the fuel lter

screen.

■

Reattach the fuel cap by turning clockwise until

reaching the physical stop (about one quarter turn).

Do not attempt to turn past the physical stop or the

fuel cap may be damaged.

■

Wipe off any spilled fuel before starting the engine.

(See Fig.

- )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita EW2051H Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info